熱氣流噴嘴 的英文怎麼說

中文拼音 [rèqìliúpēnzuǐ]
熱氣流噴嘴 英文
hot-stream nozzle
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 氣流 : 1 [氣象學] air current; airflow; wind current; airstream2 [語言學] breath氣流紡紗 open end spinni...
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. Based on the analysis of regime of spray and heat transfer, the spray nozzles were redesigned to distribute liquid in the center area of th e tower and the gas inlet was enlarged to raise gas velocity

    根據對順流式空塔的噴淋及傳熱模式的分析，重新設計了噴嘴，使噴淋液在設備中心附近集中；縮小了進氣管直徑，以提高進口氣體的流速。
  3. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  4. Abstract : this paper introduce the basic theory of the hot - wire / film anemometer and the method to determine the flow velocity of calibration nozzle system. this calibration nozzle system is designed for the calibration of hot - wire / film anemometer. a method to determine the uncertainty of this system is fully analyzed using uncertainty thoery in this paper

    文摘:介紹了熱線熱膜流速儀的基本原理和用於熱線熱膜流速儀校準用的校準噴嘴系統的氣體速度確定方法，分析和推導了用不確定度理論全面分析系統不確定度的方法。
  5. In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles

    本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
  6. This system uses a jet - flow unit nozzle to trigger hot water dynamics, converting the heat into pressure differentiation that draws external air into the tower for heat exchange to attain cooling

    （ 2 ）以一噴流單元之噴嘴引發熱水動能、轉換成壓力差，引外氣進入塔內作熱交換，達到冷卻的目的。
分享友人
分享到 Line

分享到臉書