熱矯直 的英文怎麼說
中文拼音 [rèjiǎozhí]
熱矯直
英文
thermal straightening-
With double travelling cranes, advanced 60mm punching machine, 140mm fungus type punching machine ; domestic leading 159mma r tube rolling - mills, 159mm7 rack calibrator ; the national monopoly product micro tension - reducing diameter machinery and the producer gas generator ; 40, 60, 80, 220mm straightening machine ; 5 40 tons motoblocs ; bottom rolling type continual annealing furnace ; 14m pitch type heating furnace as well as qg1118 highly effective pipe cutter and so on as well as correlated necessary facility
公司據有雙配行車的大型廠房17500平方米，先進的60mm穿孔機， 140mm菌式穿孔機國內領先的159mmar軋管機， 159mm7機架定徑機國家專利產品微張力減徑機和煤氣發生爐40 60 80 220mm矯直機540噸拉拔機滾底式連續退火爐14m斜坡式加熱爐以及qg1118高效切管機等以及相關配套設施。Qualified molten steel from the steelmaking furnace will be contained in ladle and conveyed to continuous caster, poured into crastyllizer through pouring basket, then handled with the processes of vibration, water spraying cooling, straightening, roll conveying, flame cutting, and cooling on cooling bed, finally the formed billets will be stored at the stockyard or directly sent to the heating furnace of rolling mill for heating
煉鋼爐冶煉出合格的鋼水，用鋼水包送至連鑄機，經中間包澆注到結晶器，再經振動水噴淋冷卻拉矯輥道輸送火焰切割冷床冷卻，最後存放于鋼坯堆放區或直接送至軋鋼機加熱爐進行加熱。This segregation behavior of sn accords with the mechanism of non - equilibrium segregation. it can be obtained through the theoretical calculations that the critical time of sn non - equilibrium segregation is 124 seconds at 750 and the critical cooling rate is 8 / s when cooling from 1320. it is suggested that controlling the cooling rate during continuous casting to avoid the critical cooling rate ( 8 / s ) and avoiding high stress near the trough temperature ( 750 ) may control the form
通過研究殘留元素sn的偏聚機制及其對o . 15wt . % c鋼熱塑性的影響，對試驗鋼進行脆性預測:建議在該鋼的連鑄過程中彎道矯直溫度盡量避開塑性谷底溫度750 ，二冷區的冷速盡量避開臨界冷卻速率8 / s ，從而可以減少該低碳鋼連鑄坯表面裂紋和橫向裂紋，提高其成材率。The formation process of w - type ferrite underwent from oxide of metal, the m - type transition phase to final w - phase. when the heating rate was 5 / min, at 900 for 3 hrs and 1200 for 4 hrs, pure m - type and w - type ferrites were formed in air respectively. with heat treatment temperature increasing, crystal structure was more intact, the saturation magnetization increased and the coercive force decreased
熱處理過程表明， m型鐵氧體直接由金屬氧化物反應形成，未經歷尖晶石中間相； w型鐵氧體形成由金屬氧化物到m相過渡相最終向w相的轉變；當升溫速率為5 min ，溫度在900 ，保溫3小時和1200保溫4小時，就分別形成單相m相和w相鐵氧體；隨著熱處理溫度的升高和保溫時間的延長，衍射峰變尖銳，結晶更完整，空心微球的飽和磁化強度增大，矯頑力減小。Recommended practices for heat shaping and straightening with oxyfuel gas heating torches
用含氧可燃氣體噴燈加熱成形和矯直的推薦規程分享友人