熱載體加熱器 的英文怎麼說
中文拼音 [rèzǎitǐjiārèqì]
熱載體加熱器
英文
thermal fluid heater-
The flow diagram of a lpg bottle paint - drying heating system using heat carrier as heat - medium, which has similar properties as other heat - carrier heating systems, has been improved, which has good effect in avoiding oil - spraying, shortening dehydration time and power - fail protecting etc. after making a series of analysis, calculational methods of expansion tank dimension have been deduced, which takes the moisture boiling - off of heat carrier into account and accords with real conditions
對與其它熱載體加熱系統具有共性的鋼瓶熱載體加熱系統的流程圖進行了改進和完善，在防止噴油、縮短脫水時間和停電保護等方面取得了良好效果。通過分析，整理出了熱載體加熱系統膨脹器容積的計算方法，該方法考慮了熱載體所含水分汽化而帶來的影響，比原有的計算方法更加符合實際。Traditional hydronic sizing methods can be used for selecting pumps, expansion tanks, heat exchangers, and air removal devices, as long as the heat transfer liquid ' s thermal properties are considered
傳統的液體循環加熱體量法在泵、蒸發器、熱交換器和空氣移動裝置的選擇中可以應用，在考慮載熱流體的熱血特性的情況下。The new device consists of paint - drying box, heat carrier boiler, heating pipe, expansion tank, gas separator and oil tank, etc. the data of two applied examples shows that heat carrier paint drying method is able to make painting - drying cost drop by 88 %, compared with the conventional one, that it has some advantages such as uniform temperature field, good appearance and lower costs, compared with conventional hot air convection mode
該裝置主要由熱載體烤漆爐、輻射加熱管，熱載體爐、膨脹器、油氣分離器和儲油槽等組成。應用實例的測試數據表明，與傳統的遠紅外電加熱鋼瓶烤漆方式相比較，鋼瓶熱載體烤漆節能和降低能耗費用十分顯著，能耗費用降幅達到88 。與熱風爐對流烤漆方式相比較，熱載體烤漆方法不僅節能，而且烤漆爐溫度場均勻穩定，同時烤漆的外觀質量也得到了明顯提高。The same control also activates a pump on the domestic water side that circulates water through the heat exchanger, where it is heated by the heat transfer fluid
相同的控制也會啟動在室內水側的泵，使水穿過熱交換器，在熱交換器中，水被載熱流體加熱。To the cabin which is designed by the forth department chongqing communication college, the model which includes the air in the cabin, generator set and public muffler is built integer, meshed, and added by boundary condition and load. the normal k - model etc are used to be turbulence model of the air in cabin respectively, the turbulence model is calculated by simplef or simplen algorithm, and by the first order accurate msu or the second order accurate supg in advection discretization scheme
論文對艙內空氣、發電機組和公用消聲器進行了整體建模和網格劃分，施加機組艙模型的邊界條件和載荷，採用標準k -等多個模型來分別模擬機組艙通風散熱的空氣湍流流動，採用simplef和simplen兩種不同的數值演算法以及一階msu和二階supg的對流項分離方案來對流動模型進行運算。In this paper, the in - vehicle water - heater control model is analyzed and kinds of control theory is compared. so, a scheme of the fuzzy - logic theory to the vehicle temperature control is presented
本文通過對車載液體加熱器控制模型的分析和各種傳統控制理論與方法的比較，確定了對車廂採暖進行模糊控制的方案。Uses aluminum foil as the heating transfer carrier, clings electrifying heating linear component or other shape components to aluminum foil and consequently makes into electric heating groupware. usually the needed temperature is obtained by controlling power density, insulating materials and working heat dispersion conditions etc
用鋁箔作為傳熱的載體，將加熱線通過輔助粘合劑粘合在鋁箔上，組成的片狀加熱器，從結構上可分為雙層鋁箔粘貼型單層鋁箔熱熔型。Finally, the whole heater control system scheme is drawn, then the hardware and software of intelligent instrument is designed
在此基礎上，對車載式智能加熱控制器進行系統分析，完成了系統硬體設計和軟體編程。This article guarded against explosions the heater to skid the block comprehensive support the structure to carry on the analysis ; found the question which this support structural design exists and has made the corresponding improvement design ; caused to synthesize the support the structure while to satisfy the intensity and rigidity reduced the whole weight ; tends to the optimized design in the material use ; through to synthesizes the support the finite element model to exert the different force of inertia ; obtains under the different load to synthesize the support stress variation rule, thus determine bearing capacity of comprehensive support
摘要本文對防爆加熱器撬塊綜合支架的結構進行了分析，找到該支架結構設計上存在的問題並作了相應的改進設計，使得綜合支架的結構在滿足強度和剛度的同時減輕了整體的重量，在材料的利用上趨于優化的設計；通過對綜合支架的有限元模型施加不同的慣性力，得出不同載荷下綜合支架應力變化規律，從而確定出綜合支架所能承受的最大慣性力。分享友人