熱通量濃度比 的英文怎麼說

中文拼音 [rètōngliángnóngdùbǐ]
熱通量濃度比 英文
thermal flux concentration ratio
  • 通 : 通量詞（用於動作）
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 濃 : 形容詞1. （液體或氣體中所含的某種成分多; 稠密） dense; thick; concentrated 2. （程度深） （of degree or extent） great; strong
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 通量 : [物理學] flux; shower
  • 濃度 : potency; thickness; concentration; consistence; strength; consistency; density
  1. The membrane layer is formed by the vacuum forming technology. by controlling the weight and the ratio of long path of ceramics fiber, changing the operation factor reasonably of vacuum forming, we can obtain the ceramic fiber composite membrane layer, which has pore diameters of about 5 to about 30um, porosity i s 50 - 80 %, and tensile strength is about 4. 1to 18. 1mpa and thickness of membrane layer is 0. 5 - 2 mm, has the good thermal shock resistance and peal off

    膜層採用真空抽濾成型工藝，通過控制膜組分中陶瓷纖維長徑比、纖維加入量、成型時料漿濃度、成型壓力及成型時間等可以獲得膜孔徑5 ? 30 m 、氣孔率50 ? 80 、抗折強度4 . 3 ? 18mpa 、膜層厚度0 . 5 ? 2mm 、具有良好熱性能和耐剝離性能的陶瓷纖維復合微濾膜材料。
  2. Aim : to analyze the mechanism, thermadynamic theoretical basis, dynamic mechanism and influencing factors of thermally induced phase separation ( tips ) in order to completely grasp the factors affecting the size, distribution and form of pores, so that the adjusted range of pore can be widened and the preparation of porous membrane can be repeated and controlled. methods : considering from the structural characteristics of tissue engineered materials, the methods of preparing porous membrane using tips technique, the hermadynamic theoretical basis, dynamic mechanism and influencing factors were analyzed, the problems and investigative directions in the future were also analyzed. tips technique is a process of phase separation of polymer homogenous solution under quenching, and it is suitable for diameter and structural form of the micropore materials prepared using tips are closely correlated with the kind and dispensing proportion of polymer attrnuant, polymer concentration and polymer molecular mass, etc. conducted, including determination of polymer - solvent system phase diagram, study of form and appearance of porous membrane of different thickness, study of form and appearance of porous membrane prepared with systems of different x, which is the parameter of polymer - solvent interaction

    目的:分析熱致相分離成膜過程的機理、熱力學理論基礎、動力學機制以及影響因素，以便充分掌握影響孔度大小、分佈、形態的因素，使孔度調控范圍得以拓寬，使多孔膜的制備能重復可控.方法:從組織工程材料結構特點出發，分析熱致相分離聚合物多孔膜的制備方法及該法成膜的熱力學理論基礎、動力學機制以及影響因素.並分析實驗中存在的問題及今後的研究方向.結果:以熱致相分離法可制備聚合物多孔膜.熱致相分離法制備多孔膜是高聚物均相溶液在淬冷條件下發生相分離的過程，它適用於上臨界共溶溫度型聚合物一稀釋劑二元體系.熱致相分離法成膜的過程，可以認為是旋節線機理佔主導地位.熱致相分離法制備的微孔材料，其孔隙率、孔徑大小、結構形態與聚合物稀釋劑的種類、組成配比、聚合物濃度、聚合物分子量等因素密切相關.結論:可採用熱致相分離技術制備多孔膜，通過改變不同的成膜條件可獲得一系列不同孔徑尺寸和孔徑分佈的多孔膜材料.對熱致相分離成膜過程中聚合物-溶劑體系的相圖測定，不同厚度的多孔膜形貌研究，不同x （聚合物-溶劑相互作用參數）體系所制備的多孔膜形貌等需深人研究
  3. ( 2 ) the affecting factors such as components in precipitation process, the add - on, add on of precipitator, calination temperature and calination time were studied in the preparation process of ceo2 nanoparticles. the tg was used to analyze the processor, the xrd, sem and tem were used to characterize the size of crystal type of products. by a series of designed experiments the interaction between different factors and impacts on the preparation of ceo2 nanoparticles were probed, and the optimum preparation condition was gotten

    （ 2 ）對納米二氧化鈰制備過程中可能的一些影響因素（反應組分的濃度，沉澱劑的加入量，焙燒溫度，焙燒時間等）進行了研究，並通過tg ? dta分析手段對前驅物進行熱重分析；用xrd 、 sem及tem等測試手段對產物的粒度和晶型進行分析；探索了各個因素對納米二氧化鈰制備的影響及各因素間的交互作用；確定了在該試驗條件下制備納米二氧化鈰比較優化的制備條件。
  4. Open the fluid inclusion by heat explosion, extract the ore - forming solution, measure the relative density of the ore - forming solution through its electric conductivity, and apply the results to the test of mineralization and ore - search by geological analogy

    用熱爆法打開包裹體提取成礦溶液，以電導度度量其相對濃度，以地質類比法通過從已知到未知的分析，將其結果用於成礦找礦試驗。
  5. With this coat, the bacterium is called a " spore. " the spores are so small that even an infectious dose - between 8, 000 and 10, 000 spores - is smaller than a speck of dust

    炭疽熱的孢子體積非常小，通常8000至10000個孢子達到感染濃度，這么多數量的孢子體積要比一粒灰塵的體積還要小。
分享友人
分享到 Line

分享到臉書