熱電流量計 的英文怎麼說

中文拼音 [rèdiànliúliángjì]
熱電流量計 英文
thermoelectric flowmeter
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 流量 : rate of flow; flow; runoff; discharge; throughput; （flow） rate; quantity （of flow）; flux
  1. Contraposing the measurement principle of the traditional hotwire air mass flowmeter, the reason of the excursion of the result for flow measurement was analyzed and inferred when environment temperature changed ; the method for temperature compensation and the realization circuit was given ; and compared the theory output of the new type hotwire air mass flowmeter with its real output after temperature compensation

    摘要針對傳統型熱線式空氣質量流量計的測量原理，分析和推導出當環境溫度變化時對流量測量結果產生偏移的原因；提出了一種環境溫度的補償方法和具體的實現電路；並對經環境溫度補償后的一種新型熱線式空氣質量流量計的理論輸出和實際輸出進行了計算與比較。
  2. The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality

    而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。
  3. Abstract : based on the analysis of the mathematics models of saturation steam density and superheat steam density the paper states that the deviation of the detection on temperature highly affects the accuracy of intelligent flow totalizer. especially for saturation steam ， the accuracy of the temperature detection circuit shall be designed higher than the accuracy of the instrument. thus a temperature detection circuit based on ratio method with high accuracy is introduced

    文摘:在分析飽和蒸汽和過熱蒸汽密度的數學模型的基礎上指出，溫度檢測的偏差對智能流量積算儀的精度影響極大，尤其是飽和蒸汽，測溫電路的精度應設計為遠高於儀表的精度，同時引入一種基於比率法的高精度測溫電路。
  4. As the dangerous position needed to be verified has been identified with the known heat flux profile and the characteristics of flow rate distribution, the metal tube temperature of the position can be obtained

    此方法克服了目前常用的電廠鍋爐壁溫計算方法中校核點工質流量與熱負荷並不一定互相對應的缺點。
  5. Whole scheme of frame design of test - bed is proposed as : the host fanner supply the firebox the once and twice air required by diesel oil ' s burning and the cooling air ; the export parameter of the test - bed is varied by the adjust of the flux of air and diesel oil. and the air flux is varied by adjusting the rev of the fanner adjusted by transducer and the corner of the fan inlet adjusted by step motor. the quantity of oil is varied by adjusting the oil valve adjusted by step motor ; the measurement of the air flux in the test - bed adopts the method of fanner dynamics performance test in the nation criterion

    確立了實驗臺結構設計方案：主風機為燃燒器提供燃燒所需的一次、二次進風量及冷卻風量；利用變頻器調節主風機轉速、用步進電機調節風門開度來調節風量，用步進電機調節回油閥開度來調節供油量，從而實現對模擬實驗臺出口煙氣熱流量的調節；實驗臺的流量測量採用風機動力性能測試標準中測流量方法等。
  6. The working parameters ( specific enthalpy, entropy, flux of working fluid, reynolds number, etc. ), the configuration parameters of the main components, such as steam turbine - generator group, evaporator and ehd condenser and system efficiency were calculated on the base of thermodynamics theory

    文中以熱力學理論為基礎，計算了低溫余熱發電系統的運行參數（比焓、熵、工質流量、雷諾數、管路壓力等）和各主要組件如汽輪機-發電機組、蒸發器和ehd冷凝器的結構參數，並計算了系統的效率。
  7. There are five parameters need to be measured. there are five channels for input : the displacement of casting - roller, the rotate speed of casting - roller, the pressure of casting and rolling, the casting temperature and the water - speed of cooling water. they are measured by raster, photoelectric coder, strain pressure sensor, thermocouple and turboflowmeter

    系統需要進行監測的參數有五個，即有五路輸入信號：鑄輥位移、鑄輥轉速、鑄軋壓力、澆鑄溫度、冷卻水流速，分別採用光柵、光電編碼器、應變式壓力傳感器、熱電偶和渦輪流量計作為檢測元件。
  8. In spite of the enormous improvements in foundry technology, assisted by computerized processes to optimize the design of patterns and flow geometry during pouring it is extremely difficults to achieve x - ray / mt or pt quality to class 1 or 2 acceptance standards required in hp / ht applications in nuclear, thermal power stations or severe services in petrochemical industries

    盡管鑄造技術已經有了巨大的發展，並利用計算機技術輔助優化結構設計和澆鑄過程的流體幾何設計，但是要達到1類或2類接受標準的x射線/ mt或pt質量要求仍然是極端困難的，而這些都是核電站、熱電站或石化工業內的苛刻環境所要求的標準。
  9. Design and application of the electric stove flow control system based on plc

    的電加熱爐流量控制系統的設計與實現
  10. Much works has been distributed to the development of a vacuum system to simulate the outer space and a measurement system to test the arcjet performance. ignition experiments in various operational modes have been done with argon as propellant. macroscopical working parameters including thrust, mass flow rate, voltage, current, inlet pressure and vacuity are obtained by the test measurement system and actual performance parameters including specific impulse, thrust efficiency, ratio of thrust and power and ratio of power and mass flow are calculated

    以氬氣作為推進劑，在不同工況下進行點火實驗，測量獲得了其工作推力、電弧電壓和電流、推進劑流率和弧室壓力等宏觀參數，得到了不同實驗條件下其工作的實際比沖、推力效率、推力/功率比以及比功率等性能參數，分析了推進劑質量流率、電弧功率、電弧加熱發動機電弧室結構尺寸等因素對其性能的影響，為數值模擬研究和實際的低功率電弧加熱發動機優化設計及研製提供了實驗基礎。
  11. Because coriolis mass flowmeters have directly quclity discharge of measuring he flwid measure an accarate, degree high application wide, the rearinghave low request circulate cveaibility. maintain a rate low etc, character istics extensiuely applied cure the gold thermodgnamic energy electrie power food in the petroleum chemical engintring etc discharge of the flow measure

    由於科氏質量流量計具有能夠直接測量流體的質量流量，測量準確度高，應用范圍廣，安裝要求低，儀表運行可靠，維修率低等優點，已廣泛應用於石油化工冶金熱力電力食品等領域的流量測量。
  12. In order to improve measurement precision and display fidelity of the instrument, three new methods of nonlinear calibration of thermal instruments, which are based on intelligent control theory, are presented in this paper, such as nonlinear compensation of zr02 oxygen measurement instrument using bp nn, nonlinear calibration of temperature measurement sensors using cmac nn and nonlinear identification of throttle flow meter using ga. these methods prove to be not only simple but also effective

    火電廠熱工儀表普遍存在非線性特性，為了提高參數測量的準確度和儀表顯示的精確度，基於智能控制理論，文中提出了熱工儀表非線性校正的新方法： bp神經網路補償氧化鋯氧量計非線性特性的方法、 cmac神經網路校正測溫傳感器非線性特性的方法、遺傳演算法辯識節流式流量儀表非線性特性的方法。
  13. In order to consider the different heating of positive - sequence current and negative - sequence current of the motor stator generally, the equivalent current is adopted instead of the traditional phase current. the way how to gather positive - sequence current and negative - sequence current is brought forward, and the recurrence fourier - algorithm is adopted to calculate the effective value of current and voltage, the effective value of positive - sequence current and negative - sequence current

    為了全面考慮感應電動機定子正序電流和負序電流的不同發熱效應，提出了正序電流和負序電流獲取的方法，並採用遞推傅氏演算法來實現電流、電壓及電流正序和負序分量的有效值的計算。
  14. And the influence of the heat removal in the cold and hot sides and electric current and some other factors which affect the cooling performance of thermoelectric refrigerator was also discussed by numerical calculation. furthermore, the influence of thomson effect on the performance of thermoelectric refrigerator in different refrigerating capacity and electric current was analyzed. and the work parameter of thermoelectric refrigerator was pointed out under the conditions that whether or not considering the influence of thomson effect

    通過數值計算詳細討論了穩態條件下冷、熱端傳熱系數及電流等因素對熱電製冷器製冷性能的影響，分析了在不同製冷量和不同工作電流下湯姆遜效應對溫度場的影響，指出了設計中是否要考慮湯姆遜效應的工況條件。
  15. Chart industries leads all other manufacturers in the number of cryogenic piping systems engineered, fabricated, and installed in the u. s. we combine real world experience with computer analysis to develop a system with the desired flow rate, pressure drop, phase quality, and the best balance between performance and economy

    查特公司領導著全球其他製造商，從事真空絕熱管道的設計製造和安裝。我們結合實際經驗和先進的電腦技術進行系統設計，提供合理的流量壓降液相質量，及最佳的性能-成本比。
  16. Based on the high - low voltage electric driving unit, a new electric driving unit is built, which not only has the advantages of the high - low voltage electric driving unit but also has the advantage of obtaining high limiting current and low maintaining current easily. using self - excitation chopper circuit, the electric driving unit is good efficient, and the heat creating from the solenoid is small

    在高低壓驅動電路的基礎上又設計出一種高低壓自激斬波恆流驅動電路，該驅動電路除了具有高低壓驅動電路的功能外，還具有高壓限流和低壓維持電流獲取方便、能量利用更為合理、閥發熱更少等特點。
  17. The approach is that we first calibrate the filter radiometer with cryogenic radiometer and measurement equipment of relative spectral responsivity and then calculate the absolute spectral responsivity. because the drift in blackbody temperature directly influnces measurement accuracy, so we adopt a feedback system to stabilize blackbody temperature through controlling the current of blackbody that improves measurement accuracy greatly

    該方法首先要用低溫輻射計及相對光譜響應度測量裝置對濾光輻射計進行標定，經計算可得到濾光輻射計的絕對光譜響應度；由於黑體溫度的漂移直接影響到測量精度，我們採用反饋系統通過控制黑體的加熱電流，來穩定黑體溫度。
  18. Developing instrument industry chidz has formed intellectual instruments industry, which focus on home application intelligent instruments ( water, electricity, steam and heat ), different kinds of flow meters ( liquid meters ), weighing apparatus, automation control system and nonmetallic material examination instrumentation, depending on several scienic and technological small and medium - sized enterprises

    依託十幾家科技型中小企業，初步形成了以民用智能化儀表（水、電、氣、熱） 、流量計（液位計） 、衡器、自動化控制系統和非金屬材料檢驗檢測儀器為主導產品的智能化儀器儀表產業。
  19. Sensors are used to detect the content of water and the temperature of grains, to measure the velocity of influx and to position the grains in the drying machines respectively. thermal sensors are thermocouples to monitor the temperature of heated air current and thermo resistances to measure the temperature of grains on different surfaces ; water sensors include neutron probes and condensates to measure the content of water of grains before and after drying respectively ; the velocity of flow of grains is measured by the indicators of flow

    溫度傳感器主要採用熱電偶和熱電阻，分別探測熱風溫度和乾燥機各個層面上的糧食溫度；水分傳感器主要採用中子式在線水分測量儀和電容式在線水分測量儀，中子式在線水分測量儀由於不受穀物解凍的影響，用來測量烘前穀物的水分，電容式在線水分測量儀用來測定烘后的糧食水分；在線流量計採用沖板式流量計，用來記錄排糧流量，統計產量。
  20. Flow meters may be affected, giving incorrect reading. the rate of corrosion of pipeline may also increase. the abnormal current induced in power grids may damage transformers because of overheating

    流量計可能會受到干擾，使數據失誤管道的腐蝕速度亦可能會增快電力網路上的不正常電流可能使變壓器因過熱而燒毀。
分享友人
分享到 Line

分享到臉書