熱震試驗 的英文怎麼說

中文拼音 [rèzhènshìyàn]
熱震試驗 英文
thermal shock test
  • 震 : Ⅰ動詞1 （震動） quake; shake; shock; vibrate 2 （情緒過分激動） be greatly excited; be deeply ast...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. Compementation of head shaking nystagmus and bithermal caloric test

    搖頭眼震與前庭冷熱試驗的互補作用
  2. The expressions of interaction fatigue - creep life and of thermal shock damage evaluated by modulus were obtained by the experimental analysis

    通過試驗分析，初步得到疲勞蠕變壽命表達式和模量表徵的熱震損傷表達式。
  3. Advanced technical ceramics. methods of testing monolithic ceramics. thermo - mechanical properties. determination of resistance to thermal shock by water quenching

    高技術陶瓷.整體陶瓷的試驗方法.熱機械性能.用水淬硬法對抗熱震強度的測定
  4. The damage introduced by single and 5 repeated thermal shocks ( water - quench experiments ) was characterized by degradation of flexural strength in three - point bending

    單次和5次重復熱震（水淬試驗）后經三點抗彎測試來觀察材料抗彎強度的衰減情況。
  5. Thermal shock test for toughened glass insulator

    熱震試驗對鋼化玻璃絕緣子
  6. Test method for thermal shock resistance of high performance ceramics

    工程陶瓷抗熱震性試驗方法
  7. Test methods for thermal shock resistance of high performane ceramics

    工程陶瓷抗熱震性試驗方法
  8. Test method for thermal shock resistance of castable refractory. water quenching

    耐火澆注料抗熱震性試驗方法
  9. 3d - c / sic fabricated with t300 carbon fibers weaved into 3 - dimensional and 4 - directional structure, was deposited pyrocarbon and sic matrix at 950 - 1000 with cvi method. fiber volume fraction of 3d - c / sic was 40 - 45 %, composite density was 2. 01g / cm3 and porosity was 17 %. in addition, the thickness of pyrocarbon interface was 200 nm for interaction fatigue - creep ; the interface layer of pyrocarbon for thermal shock had three thickness obtained by controlling deposition time which were 10h, 20h, 30h, respectively

    3d - c sic是用t300碳纖維編織成三維四向編織體， cvi法在950 - 1000緻密，纖維體積分數為40 - 45 ，密度為2 . 01g cm ~ 3和孔隙率為17 ，用於疲勞蠕變交互作用試驗熱解碳界面層厚度約0 . 2 m ；用於熱震試驗的有三種界面層厚度分別是熱解碳沉積時間10小時、 20小時、 30小時獲得。
  10. The pretreatment, effect of bath compositions and operation conditions such as temperature, currenty and time on compactness of the zinc and cu / ni / cr coatings have been investigated. the relationship of operation conditions to thickness of the coatings was studied by weight method. the specimens have been pickled in nacl or sulfate acid solution to evaluate the porosity of the coating

    研究了鎂合金電鍍前處理工藝，電鍍鋅、電鍍銅/鎳/鉻工藝配方及其施鍍溫度、電流密度和時間對鍍層緻密性的影響;採用稱重法研究施鍍工藝與鍍層厚度的關系，利用nacl溶液和硫酸溶液浸泡試樣來考察鍍層孔隙率，採用劃痕試驗和熱震試驗檢驗鍍層的結合力，採用金相顯微鏡和掃描電子顯微鏡觀察鍍層表面形貌。
  11. Test method for thermal shock resistance of refractory products air quenching

    耐火製品抗熱震性試驗方法空氣急冷法
  12. Test method for thermal shock resistance of refractory products water quenching

    耐火製品抗熱震性試驗方法水急冷法
  13. Glass containers - thermal shock resistance and thermal shock endurance - test methods

    抗熱震性和熱震耐久性試驗方法
  14. Test method for thermal shock resistance of castable refractory. compressed air flow quenching

    耐火澆注料抗熱震性試驗方法
  15. Thermal shock test

    熱震蕩試驗
  16. The results of static firing test shows that the thermal erosion properties, mechanical properties, tand thermal shock resistance of the c / sic composites can meet a demand for thermal - structure application in the area of aerospace such as liquid rocket thruster

    試驗發動機地面熱試車結果表明，該c / sic復合材料的力學性能、燒蝕性能和熱震性能優良，可滿足宇航工程中諸如液體火箭發動機推力室等對熱結構材料的使用性能要求。
  17. Standard test method for thermal shock sensitivity of solid film lubricants

    固態薄膜潤滑劑熱震敏感度的標準試驗方法
  18. 05. 02 wear preventive properties of lubrication greases using the ring and block test machine in oscillating motion, test for

    在震蕩運動中用潤滑劑耐熱耐壓試驗機測定潤滑脂的耐磨損特性的試驗
分享友人
分享到 Line

分享到臉書