燃料分組件 的英文怎麼說
中文拼音 [ránliàofēnzǔjiàn]
燃料分組件
英文
fuel subassembly- 燃 : 動詞1. (燃燒) burn 2. (引火點著) ignite; light
- 料 : 名詞1 (材料; 原料) material; stuff 2 (喂牲口用的穀物) feed; fodder 3 (料器) glassware 4 (...
- 分 : 分Ⅰ名詞1. (成分) component 2. (職責和權利的限度) what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] (料想) judge
- 組 : Ⅰ名詞1 (由不多的人員組成的單位) group 2 (姓氏) a surname Ⅱ動詞(組織) organize; form Ⅲ量詞(...
- 件 : Ⅰ量詞(用於個體事物) piece; article; item Ⅱ名詞1. (指可以一一計算的事物) 2. (文件) letter; correspondence; paper; document
- 燃料 : fuel
- 組件 : assembler
-
About one - third of the fuel assemblies will be replaced with new ones during each refuelling outage
在每次換料檢修均會更換三分之一的燃料組件。In the paper, in accordance with the thermal power torpedo propulsion system using hap tri - component fuel, with the i - deas software, applying the cad technology and the fem, the research of simulation on the piston - one of key parts of engine was proceeded and the paper presented the whole analysis process of the piston including thermal analysis. in the paper, the question of the boundary condition in the complicated engineering was explored and the temperature field. the stress field and the deformation of the piston were computed and analyzed under a new kind of fuel ( hap )
本文針對三組元魚雷熱動力系統,應用i - deas軟體,利用cad技術和三維有限元方法( fem ) ,對發動機的關鍵零件? ?活塞展開模擬研究,對活塞進行了包括熱分析在內的全過程的模擬計算,探索了復雜工程中邊界條件的處理問題,分析計算了魚雷發動機活塞在新型燃料(三組元燃料)工作下的穩態溫度場、應力場與變形情況,最後,根據分析結果對其結構提出了改進意見。Rubber and hose assemblies for measured fuel dispensing systems - specification
已測的燃料分配系統用橡膠和軟管組件.規范Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - specification ; german version en 1360 : 2005
已測燃料分配系統用橡膠和塑料軟管及軟管組件.規范Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - specification
已測定的燃料分配系統用帶內部蒸氣回收的橡膠和塑料軟管和軟管組件.規范There are great differences between ground test of a flight vehicle ' s aerodynamics and that of a dual - mode scramjet when ground test facilities are used to do experiments on a dual - mode scramjet engine, the components of incoming flow and its parameters, including total pressure, total temperature ( or total enthalpy ) and velocity must be simulated. at the same time, since the fuel ' s resident time within a combustor is very short, on the order of one millisecond, it is difficult to measure the flow - fields
進行雙模態沖壓發動機地面試驗研究時,必須要求試驗設備能模擬實際飛行條件下來流氣體的組分、總壓、總溫(或總焓)以及來流氣體的流動速度;同時由於燃料在燃燒室內駐留的時間很短,一般為毫秒量級,從而使流場物理量的測定顯得非常困難。The paper describes the heat treatment at the temperature of 160, 250, 350, 400, 450 and 500, the dimension change and microstructural evolution of miniature fuel element plates after heat treatment. the result reveals that : the fuel plates did not deform after 60 days at 160 and 250, slightly curved after 60 days at 350 and 400, and heavily curved after 20 days at 450 and so did after 1 day at 500
本論文介紹了微型燃料元件板(芯體u _ 3si _ 2 - al ,包殼為6061鋁)的熱穩定性實驗研究,在160 、 250 、 350 、 400 、 450 、 500溫度下經過一定的熱循環,測定燃料板的變形,進行微觀組織分析,結果表明:在160 400范圍四個溫度循環熱處理60天後,燃料板厚度變化均小於0 . 03mm ,在前兩個溫度下,基本沒有變形;在後兩個溫度下,燃料板稍有捲曲。Methods of test for rubber and plastics hoses and hose assemblies - hydraulic pressure tests - determination of volumetric expansion of fuel - dispensing pump hoses
橡膠和塑料軟管及軟管組件試驗方法.第102部分:液壓試驗.第3節:燃料分配泵軟管體積膨脹測定This paper presents in detailed the design and fulfillment of the hardware and software of a measuring system for fast neutron reactors and fuel, and emphasis is placed on the design and fulfillment of the software
本論文詳細介紹了快堆組件套管及燃料棒測量系統中的電控部分和測量控制軟體部分的設計及實現方法。Equipment for commercial kitchens - components for ventilation - part 7 : installations for treatment of cooking fumes, requirements and testing
商用廚房設備.通風組件.第7部分:處理烹飪燃料用設備Methods of test for rubber and plastics hoses and hose assemblies - physical tests - determination of resistance to fire
橡膠和塑料軟管及軟管組件試驗方法.第103部分:物理試驗.第13節:抗燃性測定分享友人