燃油噴口 的英文怎麼說

中文拼音 [rányóupēnkǒu]
燃油噴口 英文
fuel jet
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 燃油 : fuel oil燃油艙 [船舶工程] oil bunker; oil fuel tank; 燃油閥 fuel valve; 燃油鍋爐 oil burning boil...
  1. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  2. Evaluation for configuration characteristic of reentrant combustion chamber on heavy - duty di diesel engine

    重型直噴柴油機縮口燃燒室結構特點與評價
  3. Finally, the inlet port and combustion chamber designed and machined is tested on 4100qb. the paper mostly investigates the change of performance targets of the engine that three different grooved chambers including two different re - entrant model and one w model match with various intake port and nozzles, in order to realize the influence of chamber geometry on combustion process. the results analyzed have indicated that re - entrant grooved chambers can enhance the turbulent intension in the chamber, improve the combustion proces of diesel engine on the altiplano, being groove, re - entrant and convex, and have the farther developing potential

    著重研究兩種縮口、一種直口矩形環槽燃燒室與不同進氣道、噴油嘴的組合方案發動機的動力性、經濟性及排放指標的變化，確定燃燒室的幾何形狀對燃燒過程的影響。分析結果表明，由於有矩形環槽、燃燒室縮口以及燃燒室底部凸臺，縮口矩形環槽燃燒室中的紊流得以加強，改善了高原柴油機的燃燒過程，這種燃燒室有進一步發展的潛力。
  4. Test method for evaluating automotive spark - ignition engine fuel for electronic port fuel injector fouling by bench procedure

    火花點燃式汽車發動機燃油電子口噴油器結垢的工作臺評定試驗方法
  5. Standard test method for evaluating automotive spark - ignition engine fuel for electronic port fuel injector fouling by bench procedure

    Bench法評定電子口燃油噴射器結垢情況用汽車火花點燃式發動機燃油的標準試驗方法
  6. In the text, there analyzes the process of the mixture air and fuel in the two stroke gasoline engine and bring forward the specific solution to the improvementsing gasoline engine the high - press direct in - cylinder injection. this technology sprays the feul into the cylinder after the outlet vavle closed and scavengs the engine cylinder with pure and fresh air, which avoid the fuel escapes unburned

    本文分析了二沖程汽油機混合氣形成過程，並提出了具體的改進方案，用缸內高壓直接噴射技術進行改造。缸內高壓直接噴射是在發動機排氣口關閉後向氣缸內噴射燃油，使用純新鮮空氣進行掃氣，避免了燃油短路損失。
  7. Standard test method for evaluating unleaded automotive spark - ignition engine fuel for electronic port fuel injector fouling

    對汽車無鉛火花點火發動機油進行電子口燃油噴口結污評定的標準試驗方法
分享友人
分享到 Line

分享到臉書