燃燒器噴口 的英文怎麼說

中文拼音 [ránshāoqìpēnkǒu]
燃燒器噴口 英文
burner nozzle
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。
  2. In this paper, simple reacting flow model in solid - propellant ducted rocket combustor based on eddy break - up model is established. the model is used to simulate the three - dimensional combustion flowfields in an experimental motor. some factors how to affect the combustion efficiency are discussed in the paper, including air intake and gas generator nozzle

    本文基於簡單反應的旋渦分裂模型，建立了固體火箭沖壓發動機補燃室內的湍流燃燒模型，並在該模型下對某實驗發動機進行了三維數值模擬，研究了補燃室設計參數包括進氣道出口設計參數和燃氣發生器噴管設計參數對燃燒效率的影響。
  3. Combustion system of power plant boiler is taken as the research object of this thesis. the research mainly focuses on the faults of boiler combustion system, such as flame center deflection, powder feed inequality or break, primary air pipe jammed, spontaneous combustion, and backfire or kill in burner spout

    本文以電站鍋爐燃燒系統為研究對象，主要圍繞鍋爐燃燒系統運行中可能出現的爐膛火焰中心偏斜、給粉機下粉脈動、一次風管道內堵粉、自燃、燃燒器噴口回火、滅火等故障展開研究。
  4. These measures are as follows : shorten the primary wind intervals to improve thermal load of the burner ; reduce the size of hypothetical circle of contact to prevent the flame from splashing ; use nozzles with larger height / width ratio to increase the effusive rigidity, so as to increase the jet flow depth of secondary wind into the main jet flow ; use a higher primary wind velocity to increase its jet flow rigidity ; use a special flame holder structure of the primary nozzle, so as to improve

    這些技術措施主要有:縮小一次風間距以提高燃燒器區域熱負荷;縮小假想切圓防止火焰刷墻;採用高寬比較大的二次風噴口以增加射流剛性，提高二次風射流進入主射流的深度;採用較高的一次風速來提高一次風射流剛性;一次風噴口採用特殊穩燃結構;提高下二次風的托粉能力。
分享友人
分享到 Line

分享到臉書