燃燒滯后 的英文怎麼說
中文拼音 [ránshāozhìhòu]
燃燒滯后
英文
combustion lag-
Because of its extensive application and underdeveloped research level in our country, this paper establish the numerical model of blank cartridge ejecting device, the whole process from blank cartridge burning to eject missile is analyzed by classic interior ballistic theory and gas dynamics. several simulation examples are given, and the effect of different parameter structure on ejecting device is discussed
鑒于這類系統在我國的廣泛應用與相對滯后的研究水平，本文針對三種類型五種型號的掛彈鉤建立了拋放彈彈射機構的數學物理計算模型，用經典內彈道和氣體動力學理論分析了火藥彈燃燒到彈射活塞完全推離懸掛物的整個過程。However, cfb technology itself is developing fast, and the combustion process of cfb is highly non - linear, with high uncertainty, large time delay and high multi - variable coupling, making the process complicated. so far, the research on the combustion mechanism and its fuzziness is immature, therefore, there is no good model for real - time control of the process
但是，迄今為止循環流化床鍋爐仍然是一種工藝上不斷改進的新型鍋爐，它的燃燒過程具有高度的非線性、不確定性、時變和大滯后，及多變量耦合嚴重等復雜特性，尤其是目前對其燃燒機理和模糊化的研究不太成熟，還沒有能用於實時控制的完善的模型。So that tar burnt in completely and not clinging to the wall of sleeve will prolong service and reduce te mperature delay
這樣使未燃燒完的焦油不易粘在套管外壁，延長壽命，減少溫度的滯后性。For big hysteresis control, response time is long and overmodulation is big, but dynamic performance figure is not good when we only use pi controller 。 so, i try to design the whole control project which composed of the vapor wraps water level control system and combustion control system use the control equipment of double cross - parameter fuzzy - pi controller
單獨採用pi控制，對大滯后控制，響應時間及超調很大，但動態性能指標差。因此，嘗試採用雙交叉參數fuzzy - pi控制器。組成了汽包水位和燃燒雙交叉參數自調整fuzzy ? pi組合控制器的整體控制方案。A study of combustion of the furnace in high - speed - wire factory of tangshan steel company is made, from which the conclusion is acquired, that is the process is a casual process of nonlinear and distributed parameter with big inertia, pure lag and casual disturbance. this makes prepare for further studies
研究了唐山鋼鐵公司高線廠的蓄熱式加熱爐的燃燒情況，得出了結論，即其過程為大慣性、純滯后、受隨機干擾的非線性分佈參量過程，為后繼的研究作了準備。The main research work and contribution of this dissertation are as follows : l. a study of combustion of the furnace in high - speed - wire factory of tangshan steel company is made, and conclusion is acquired, that is the process is casual process of nonlinear and distributed parameter with big inertia, pure lag and disturbed by casual factors
本文的主要研究的內容有如下幾個方面： 1研究了唐山鋼鐵公司高線廠加熱爐的燃燒情況，得出了結論，即其過程為大慣性、純滯后、受隨機干擾的非線性分佈參量過程，為后繼的研究做了準備。分享友人