燒到粘結 的英文怎麼說
中文拼音 [shāodàoniánjiē]
燒到粘結
英文
dead burning-
Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer
超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。While adding 1 % binder the preferable target was produced, and the density was 4. 89g. cm - 3, which was 88 % of the theoretic density of the licoo _ 2 with ar as the sputtering gas, the technics of rf sputtering to produce the licoo _ 2 film were studied systematically
在冷壓燒結方法制備licoo _ 2靶材的過程中，燒結前添加了不同量粘結劑，就綜合純度和粘結性能兩方面考慮，加入1 %的粘結劑較為理想。所制備的licoo _ 2靶材密度為4 . 89g / cm3 ，達到licoo _ 2理論密度的88 % 。It was found that the thickness of the film can improved with adding some mucilage glue. a low temperature sinter can acquire a transparent sio2 film on the gold electrode
增粘劑的加入可提高一次塗膜的厚度，低溫燒結可在金電極上得到表面光亮的二氧化硅玻璃薄膜，絕緣性能良好。In this thesis, the sls molding properties of some metal - base composite powders composed of metal powder mixed by several regularly used polymers " powder were studied, on the basis of which, a new sls composite material made by 316 stainless steel powder mixed by epoxy powder was developed and produced. the molding technics and adherent mechanism of the material in sls process was analyzed and studied, and the high temperature sintering technics of the green parts of the material was discussed as well
本文主要針對快速成型的sls方法，研究比較了幾種常用的聚合物粉末添加到金屬粉末中所構成的金屬基復合粉末的成型性，並且研製開發了316不銹鋼粉末與環氧樹脂粉末共混復合粉末作為成型材料，對其sls過程的成型工藝、聚合物粘接機理以及型坯的高溫燒結工藝進行了研究論述，並進一步對型坯的高溫燒結過程、燒結中的收縮變形和燒結后的強度作了分析研究。The air - powered machine of chopper because of having structure in brief, maintenance convenient, the cost was low and otherwise advantages to get an extensive application, but often took place breakdown on control circuit of air providing in actually running, causing the contact point of relay to glue together and burning it to bad, the air pressure getting unusually state and the like other serious obstacle
高壓斷路器氣動機構由於具有結構簡單，維護方便，成本低等優點得到了廣泛的應用，但在實際運行中常發生氣體打壓控制迴路故障，導致接觸器接點粘連燒壞，氣體壓力異常等嚴重障礙。分享友人