燒成時間 的英文怎麼說

中文拼音 [shāochéngshíjiān]
燒成時間 英文
firing time
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 燒成 : baking
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. The simulation results suggest that, at the end of the scanning line, the dissymmetric temperature field and the great temperature gradient result in the balling phenomenon and great thermal stress, which could lead to the destruction of the sintering samples in this region. because of the coupling effect between scanning lines, the balling phenomenon is increased as the increase of the scanning lines, thus the over short scanning lines should be avoided in the sintering process. different scanning strategies have significant influence on the sintering

    模擬結果表明，掃描端點溫度場的不對稱及較大的溫度梯度造成了端點球化現象，並在端點處產生較大的熱應力，使燒結成形試樣易在此處破壞;激光掃描線間的耦合作用使端點球化現象隨掃描線的增加而逐漸顯著，燒結時應避免過短的掃描線;不同掃描策略對燒結成形有很大影響，交替掃描會影響燒結試樣的質量，實際製造時應採用單向掃描策略。
  2. “ we have looked to gain performance by increasing the peak revs, and improving areas like cylinder filling and combustion, ” explained denis chevrier, renault ' s head of trackside engine operations. “ in qualifying trim, we expect a gain of several tenths of a second and the final dyno tests before the grand prix will allow us to determine exactly how much additional performance is available during the race

    「我們看上去已經通過增加最大轉數取得了成績，並改善了像汽缸填塞和燃燒這樣的區域」雷諾賽道引擎運作負責人丹尼斯-謝維瑞爾解釋說， 「在排位賽中，我們期待能獲得零點幾秒的時間，大獎賽前的最後測試會允許我們最終決定可以在正式比賽中有多少的附加表現。 」
  3. Based on orthogonal designed experiment, the synthesis of corundum - mullite - gahnite multiphase materials by two - step sintering process showed that the light fired temperature and holding time mostly influenced the apparent porosity of the multiphase materials. further study on the light firing time indicated that at the light firing temperature of 1300 and died fire temperature of 1600 for 3h, the optimal light fired time was about 1h

    二次煅燒及正交實驗合成復相材料研究表明：輕燒溫度和輕燒時間對復相材料的顯氣孔率影響顯著；通過輕燒保溫時間的進一步研究表明：含剛玉、莫來石、鋅鋁尖晶石的復相材料，在輕燒溫度為1300 、終燒條件為1600下保溫3h時，最佳的保溫時間為1小時左右。
  4. The effects of calcinations temperature and holding time on the perovskite phase of synthesized pmn - pt have been studied

    並研究了煅燒溫度及保溫時間對合成材料單相性的影響。
  5. The investigation has declared that the fuel injection with bq fuel pump had higher injection pressure, bigger fuel supply rate and shouter fuel supply duration, which would cause the fuel injection quantity and the fule - air mixture to increase during ignition delay period, the pre - mixed combustion to become acutely, and finally result in increased power levels of noise

    研究表明，裝配bq噴油泵，噴油系統的噴油壓力較高，供油速率較大和供油持續時間縮短，使得滯燃期的噴油量增加，滯燃期內形成的可燃混合較多，預混燃燒劇烈，導致整機噪聲聲功率級增加。
  6. When sufficient wollastonite is added to ceramic material, the baking temperature can be decreased ang the baking duation greatly shortened to one rapid low temperature bake, thus saving fuel and reduing production costs

    在陶瓷原料中加入適量的硅灰石，可以大幅度降低燒成溫度，縮短燒成時間，實現低溫快速一次燒成，大量的節約燃料，明顯降低產品成本。
  7. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  8. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  9. The expansion and dehiscence behavior during the vacuum reactive sintering below 660 of compact ti / al composite powders was experimentally investigated, and the reasons of expansion and dehiscence were theoretically analyzed. the method of low temperature reactive sintering was generalized, and the experiment testified the method effective. the rule of the expansion of the billets was generalized from the result of density of the billets

    低溫反應燒結工藝:研究了高能球磨ti / al復合粉體在溫度低於660下真空無壓反應燒結過程中的膨脹和開裂行為，分析了產生膨脹和開裂的主要原因;並提出了能夠有效預防坯料開裂的方法;通過測定坯料在低溫燒結后的密度，總結了其體積膨脹的規律;通過x射線衍射技術分析了隨球磨時間不同，金屬間化合物的生成情況。
  10. After the sample is turned out, its internal and external structures are observed and its bulk density is measured in order to determine how the sintering temperature, the time of thermal preservation, and the quantity of admixture affect the performance of lytag

    通過對試樣內、外部結構觀察和容重的測定，研究燒成溫度、保溫時間及外加劑摻量對粉煤灰陶粒性能的影響。
  11. By the investigation for preparation technique of the phosphor, the optimum activator concentration, host composition and firing time were established

    通過對熒光粉制備工藝的研究，確定了熒光粉制備中最佳的激活劑濃度、基質的組成及樣品的灼燒時間等工藝參數。
  12. The experimental data has been used to validate pdm and low temperature sintering mechanics. the advantage and disadvantage of pdm have been discussed also. for the first time, the pdm is used to study the low temperature sintering mechanics of uo _ 2, and the research results indicate : 1

    3 、基於燒結頸長大速率與緻密化動力學方程得出，影響二氧化鈾低溫燒結的因素有原始粉末粒徑、粉末堆積方式、坯塊原始密度、燒結溫度、燒結時間、燒結氣氛等;粉末壓坯一定時，燒結溫度、燒結時間和燒結氣氛就成為控制低溫燒結的關鍵因素。
  13. The microwave magnetic sintering can not only lower the sintering temperature and shorten the sintering time, but also decrease the micro - grain size of magnets and make intergranular phase and grain boundary of main phase distributed well. the abnormal grain growth was found in conventional sintered ndfeb magnets, which may be due to the greater particle size and uneven distribution of powder, and higher sintering temperature and longer sintering time. of course, the abnormal grain growth would deteriorate the magnetic properties

    微波磁場燒結的不但降低燒結溫度，縮短燒結時間，而且使磁體整體加熱，受熱更均勻，因而磁體晶粒更細小，並且主相晶粒邊界趨于規則化，晶間相的分佈更均勻；在常規燒結的磁體中則出現了晶粒異常長大現象，造成這一現象的原因，一方面可能是燒結溫度過高或燒結時間過長，另一方面可能是磨製的粉體均勻性較差，存在的大顆粒被許多細小顆粒包圍，在燒結過程中，大顆粒不斷吞併小顆粒，逐漸長大，而異常長大的晶粒自然會導致磁體性能的惡化。
  14. As shown by the measurements, the electrical resistivity of sintered psc has a tendency of first decreasing and then increasing as the sintering temperature and / or sintering time increase. also it decreases with the increased pressure on the pressed powder compact

    對樣品的電阻率進行了測量，總體呈現出隨燒結時間和燒結溫度的增加而先降低后增加的趨勢，並隨壓坯的成型壓力的增加而降低。
  15. Results showed that the factors include : solvent and concentration of limn204 precursor solution, spin - coating speed, heating speed, sintering temperature and time etc. in the end, techniques of sintering under vacuum conditions were studied

    主要有以下幾方面:溶液中離子總濃度以及分散劑濃度對成膜質量的影響;旋轉塗覆時轉速、熱處理的升溫速度、燒結溫度、燒結時間對薄膜晶型結構及性能的影響。
  16. Cr particles were enclosed by cr - w solid solution alloy after cr powder and w powder were sintered if the grain size of cr powder is larger than w powder. around cr particles more cr - w solute was formed with prolonging sintering time. during infiltration process, cr was dissolved and moved into the pores in w skeleton by cu liquids and made w skeleton become w - cr skeleton

    粒度較大的cr粉和粒度較小的w粉混合燒結后，形成crw固溶體合金包圍cr塊的組織形貌，燒結時間越長， cr塊周圍形成的crw固溶體越多；熔滲過程中， cr被cu液溶解並轉移到w骨架之間的孔隙中， w骨架則轉變為cr - w骨架。
  17. The sample composition was analyzed by means of tg and x - ray diffraction. the following conclusions can be drawn from the experiments : given conditions, the sample powder that has the same xrd data as the standard fetioa can be gotten when use any method mentioned above ; the key in synthesis is to avoid the oxidation of fe2 +, so the whole process should performed under vacuum or neutral atmosphere, samples used by this study were prepared under nitrogen atmosphere ; the heat - treated time and temperature have some influence on the sample powder, results show that the proper time and temperature is 120 minutes and 1100 respectively

    研究結果表明：在合適的反應條件下，用上述三種合成方法都能得到xrd數據與標準fetio _ 3物相基本吻合的粉體；合成反應需要克服的主要問題是防止體系中fe ~ （ 2 + ）的氧化，因此，整個反應必須在真空或者非氧化性氣體保護下進行，本研究需要的樣品是在高純從保護下合成的；煅燒的時間和溫度對最終的產物也有一定的影響，研究發現：合理的煅燒時間和溫度分別為120分鐘和1100 。
  18. At the same time, a modified calcination method was first put forward, that is, after the first calcination, additional annealing was enforced. by the use of the thermal analysis, xrd, partical size, specific surface area and electrochemical measurement, the structure and performance of the product were studied, and the synthesis process was optimized by comparing structure and performance with one another

    通過優化合成工藝，發現ph值在2 3之間、 paa與金屬離子的摩爾比為1 . 4 ： 1 、燒結溫度為550 、燒結時間在10h左右時所得產物有良好的結構和電化學性能。
  19. To micrometer sic powder, pressed compacts were made under 750 mpa pressure with sintering time ranging from 4 to 7h and sintering temperature ranging from 1600 to 1800 @, but to nanometer sic powder, pressed compacts are made under1000 mpa pressure with sintering temperature being 1600 ? and sintering time ranging from 4 to 5h. howerver, all compacts were sintered under an ar protection of 1. 0 atm pressure

    對于微米粉末，壓坯在750mpa壓力下壓製成型，燒結溫度為1600 1800 ，燒結時間為4 7h ；而對于納米碳化硅粉末，壓坯在1000mpa壓力下壓製成型，燒結溫度為1600 ，燒結時間為4 5h ，所有壓坯都在1 . 0atm的ar
  20. Many methods were adopted to research the cathode material lifepo4 from different facets, which are concluded as the following : firstly, the cathode material lifepo4 was synthesized successfully by microwave caicination using acetic acid lithium, oxalate ferrous iron and ammonium dihydrogen phosphate

    工作主要包括以下幾個部分: 1 .採用微波合成法，成功制備出橄欖石型結構正極材料lifepo _ 4化合物。在本文實驗條件下，最合適的微波燒結時間為10min 。
分享友人
分享到 Line

分享到臉書