燒結塗層 的英文怎麼說

中文拼音 [shāojiētúcéng]
燒結塗層 英文
sinter coating
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 塗 : Ⅰ動詞1 （抹） spread on; apply; smear 2 （亂寫或亂畫） scrawl; scribble 3 （抹去） cross [blot; s...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 塗層 : paint-coat; paintcoat; coat; coating; covering; lining; wrapping flux
  1. The sbf cultivation results by different surface modification methods were : nano - tio2 coating > alkali solution treatment > tio2 coatings sintered in normal pressure > tio2 coatings sintered in vacuum

    不同表面改性方法的sbf培養結果比較為：納米二氧化鈦塗層堿液處理方法常壓下燒結二氧化鈦塗層真空下燒結制備的塗層。
  2. 6, the formation of nano - nano sic / al2o3 composite ceramic coating : the heating difference of the powder in - outer layer during spraying results in that the inner nanoparticles are only partially melted, without growing into larger grain, a lot of nanoparticle agglomerates with sintered shape were detected in the coating

    6 、納米?納米sic al _ 2o _ 3復相陶瓷塗層形成過程為：乾粉顆粒內外層在噴塗過程中受熱歷史不同，導致內層納米粒子僅僅熔化而沒有結晶長大，塗層中形成了許多呈燒結形態納米粒子構成的團聚體。
  3. So the titanium dioxide coatings were fabricated by cladding substrates to sinter in different work mediums, which included normal pressure and vacuum conditions. the surface morphology and phase constitution of coatings were analyzed

    本研究採用包埋燒結法分別在常壓和真空條件下在鈦合金試樣上制備二氧化鈦功能塗層，並對塗層的表面形貌和相組成進行了分析。
  4. Abstract : in this paper, the workmanship of reactive sintering of thermal spray coating, microstructure and bonding property are introduced

    文摘:介紹了熱噴塗層的中溫反應燒結工藝，及其組織結構的特點和塗層結合性能。
  5. The antiablation of silicone rubber liner can be improved both by changing the structure of unvulcanized rubber and adding antiablative fillers, and the bond strength between propellant charge and the liner would be increased largely by coating the primer liquid on the charge surface

    硅橡膠包覆層中填料的粒徑對硅橡膠的補強效果十分重要；可從改變生膠結構、添加耐燒蝕填料兩方面來改善硅橡膠包覆層的耐燒蝕性；在推進劑藥柱表面上塗覆底塗液可以大幅提高硅橡膠包覆層與推進劑的粘接強度。
  6. The permittivity and reflectivity of absorbing coating of moo3 - v2o5 - p2o5 - fe2o3 glasses doped with si / c / n nano powder were researched

    研究摻雜納米粉體的吸波塗層的燒結工藝及其介電常數和反射率。
  7. It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature. the chemical state of the elements ti and si at the coating interface varied. the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy

    通過研究發現， bg塗層與基體的結合強度與基體表面的粗糙度以及燒成溫度密切相關，塗層界面處ti元素和si元素的化學狀態發生了變化， bg與基體強結合的機制為化學鍵和機械嵌合兩種力共同作用。
  8. Steel tubes. external polyethylene coating. application by powder sintering

    鋼管.聚乙烯外塗層.粉末燒結的應用
  9. The nanoparticles coating was fabricated by cladding titanium alloys with nano - tio2 powders, and its surface roughness was 2. 1 - 2. 3 m which was smaller than that of ordinary titanium dioxide coatings

    用納米二氧化鈦粉包埋鈦合金試樣燒結制備的塗層表面粗糙度值ra在2 . 1 2 . 3 m之間，相對于普通二氧化鈦粉包埋燒結的塗層來說，粗糙度較低。
  10. Abstract : the influence of re - addition way and sintering temperature on such physical and chemical characteristics as the ability of enameling glaze has been investigated in this paper. and the research has shown that the structure of glaze will be transformed from amorphous state into crystalline state and the grains will be refined while the sintering temperature and re content are increased

    文摘:本文研究了在瓷釉中加入稀土的方式、燒結溫度對瓷釉的塗搪性等物理性能以及化學性能的影響，並發現，隨著燒結溫度和稀土含量的增加，瓷層結構由非晶態向晶態轉變，晶粒細化。
  11. Study on erosion wear of wc - co coatings prepared by supersonic plasma spray and hvof spray

    熱噴塗中溫燒結塗層的顯微組織和磨損性能研究
分享友人
分享到 Line

分享到臉書