爐中結塊 的英文怎麼說
中文拼音 [lúzhōngjiēkuāi]
爐中結塊
英文
bear-
The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。We select ni / cr alloy resistor as element together with ceramic embedding hearth ; select small flat - and - disc heat - even hubby ceramic sample holder, select ni / cr & ni / si thermoelectric couple ( type k ) as thermoscope with threads 0. 5 mm in diameter which is installed in the middle of the holders symmetrically ; select aluminum silicate fire - retardant fiber as materials for heat preservation ; design some hardware, for example temperature controller & transporter, signal amplifier etc ; design controlling curve to heat stove ; and introduce the method of least squares nonlinear regression and subsection function to deal with data. in order to obtain the reasonable operation conditions and operation curve, we have also done many theory analysis and experiment discussions
通過理論和試驗探討，選用鎳鉻合金電阻絲作為加熱元件，配以陶瓷質埋入式爐膛；選用陶瓷質小尺寸扁平?圓盤均熱塊體型樣品支持器；選用0 . 5mm絲徑鎳鉻?鎳硅熱電偶（ k ）作為測溫元件；熱電偶對稱安置在樣品支持器容器的中部；選用硅酸鋁耐火纖維作保溫材料；合理選用和設計了溫度控制器、溫度變送器、信號放大電路等硬體；採用升溫曲線來控制爐膛供熱過程；採用最小二乘法非線性回歸與分段函數相結合的曲線模擬方法，進行圖形處理。Microstructure of the composite layer was analyzed with help of optical microscope, scanning electronic microscope ( sem ), electronic probe microanalysis ( epma ) and x - ray diffraction ( xrd ). the compacting of the billet and the forming mechanism of the carbide reinforcement were studied based on thermodynamics and kinetics of reaction, sintering theory and the result of dta. at the same time, the wear - resistance of the composite layer was studied under condition of dry sliding friction
利用光學顯微鏡、掃描電子顯微鏡、電子探針以及x -射線衍射儀，分析了表面復合層的基體組織結構；運用反應熱力學、動力學、粉末燒結理論和燃燒合成理論，結合差熱分析結果，探討了表面復合層壓坯的燒結緻密化原理和碳化物增強相的形成機理；利用坯塊在真空燒結爐不同溫度下的燒結出來的顯微組織分析，模擬出坯塊的燒結過程中的化學反應過程。
分享友人