特形噴管 的英文怎麼說
中文拼音 [tèxíngpēnguǎn]
特形噴管
英文
shaped nozzle-
Abstract : the formation technologies, the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied. the results indicate that the rheological behaviour and spinnability of commixed polyester melt, and the structure and properties of the fibre, are relative to the spinning temperature, melt pressure, microporpus size for spinning, formation conditions, thermo - vascellum temperature, thermo - vascellum position and rolling speed, besides the viscosity of polyester cuts, coacervation particles, adding amount and size of micrometallic - oxide
研究表明， tcs微孔化共混聚酯熔體在成型加工中的流變行為和可紡性，及其纖維的結構性能除了與原料切片的特性粘度、凝聚粒子和共混聚酯中超細金屬氧化物微粒的添加量、粒徑等因素的影響有關外，還與紡絲溫度、紡絲熔體壓力、噴絲板微孔尺寸、冷卻成形條件、熱管溫度、熱管安裝位置以及卷繞速度等因素的影響密切有關。According to the feature that deformation resulted from water absorption and mildew appear mainly on the rabbet surface of ccf, this paper adopts rsst to spray a special waterproof sealant on rabbet surface of ccf, so that the sealant can get into fiberboard to certain extent by means of capillarity and penetration, blockage the holes between fibers and capillary, cut up passage of water and change the properties of soakage and sorption to water in capillarity and fiber. at the same time, solidified sealant can form a compact waterproof pellicle on rabbet surface so as to prevent water and humidity from fiber ' s expansion and mildewing
針對吸水變形、霉變主要發生在地板企口表面的特徵，採用企口表面全封閉法，在復合強化地板企口表面噴塗特殊的防水封閉劑，使其依靠毛細管作用及滲透作用進入板內一定深度，堵塞木纖維之間的空隙及毛細孔通道，截斷水分傳遞的渠道，並改變毛細孔壁及纖維的表面性質以不利於水的浸潤與吸附，同時其固化后能在企口表面形成一層緻密的憎水薄膜，防止水分、濕氣從企口侵入板內引起木纖維膨脹變形、發霉等現象。The application background of thrust vectoring technology on aircraft and its advantages are analyzed. the main characteristics of some type of vectoring nozzles are discussed, the expression of thrust vectoring force and moment are set up. then, the nonlinear motion equations of aircraft with three axes of thrust vectoring are deduced
本文主要針對推力矢量飛機非線性飛行控制的理論和應用問題進行了一定的探索和研究，進行的主要工作有： 1 、研究了推力矢量在飛機上的應用背景和收益，分析了現有推力矢量噴管的主要形式和特點，給出了推力矢量力、力矩的數學模型，並在此基礎上推導了帶三軸推力矢量飛機的非線性運動方程，為控制律的設計奠定基礎。The protective tube is made from special high temperature alloy steel and drilled, also coating round its surface to form double protection and prolong service life up to over a year
套管本體採用特殊高溫合金鋼，整體棒料鉆孔，表面經噴塗工藝處理，形成雙重保護，極大地延長了熱電偶的使用壽命，壽命可過一年以上。The research indicates that the orifice jet in mixing conditions has many different points from the pipe jet. focusing on the jet ejected from the orifices of different diameters and lengths, this paper studies the orifice jet when the fluid upstream of the orifices is in mixing conditions. the main purpose is to qualitatively study the effect of orifice diameters and lengths on the spread of the jet
射流是在工程實際中廣泛存在的一種流動現象，噴嘴出口的流動狀態對射流的發展有很大的影響，前人對射流的研究主要集中於噴嘴前流體是完全發展管流的情形，本文研究了全混狀態下的板式射流，研究結果表明全混狀態下的板式射流具有很多不同於管射流的特點。分享友人