率定水槽 的英文怎麼說

中文拼音 [lǜdìngshuǐcáo]
率定水槽 英文
rating flume
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 水槽 : water channel; trough; pentrough; mantle; water slide （運木材用）; cistern; scoop channel; gulle...
  1. Soak specimen in warm after a specified time then observe whether specimen surface had degenerative conditions as blister, fadeaway, swell. … etc. to judge its quality and calculate the change rate of weight before / after test

    恆溫水槽：材料經本水槽一定時間之溫水浸漬試驗后，觀察是否變質，表面有無起泡、褪色、膨脹等現象，以判暄品質，亦可計算試驗前後之重量變化率。
  2. In this paper, we study the most serious damming section of the east - one main canal, which is from the entrance of the hao wan flume ( chainage12 + 123. 6 ) to the exit of shang tian yuan tunnel ( chainage24 + 091. 1 ). the main content is analyzing the flow characteristic of the canal, setting up mathematical model of the discharge condition of the east - one main canal, according to the survey section and actual roughness factors, building, bend and so on, we divided the canal into more than loocaculation segments. each segment is calculated by microsoft excel electrical table through computer as permanent transition flow of non - prismatic channel

    本論文研究的渠段為陸渾灌區東一乾渠壅水最為嚴重的渠段，從郝灣渡槽進口（樁號12 + 123 . 6 ）至上天院隧洞出口（樁號24 + 091 . 1 ） ，其主要內容是，分析渠道水流特徵，建立東一乾渠輸水狀況的數學模型，根據測量斷面及實際糙率、建築物、彎道等因素的不同，將渠道劃分成120多個計算段，每段按非稜柱體恆定漸變流，運用microsoftexcel電子表格進行編程計算。
  3. Fmc closed air insulation wire tank is a new products designed and developed by us and its techniques and craft has reached the requirements of high graded products in the 1990s. it s suitable for the following conditions : four - wrie system or five - wire system,

    Fmc空氣絕緣型封閉母線槽是我公司自行研究開發的新產品，生產技術及製造工藝要求達到九十年代國內先進水平的母線槽電器產品，適用於交流三相四線制三相五線制，頻率50 60hz ，額定工作電壓至660v ，額定工作電流250 - 5000a的供配電系統，主要用於現代化廠房車間和高層建築等場所。
  4. The millimeter has the largest frequency band and the highest velocity of communication, but it has the highest cost and technical defaults : multi - path effect, reflect and scatter caused by cloud, smoke, water - dropping, the buildings, the grounds and its shape, the interference caus ed by the thunder, the complexity of device, difficult maintenance, and so on. now the band of the leakage coaxial line is up to 3ghz, leakage coaxial line has some advantages : good adaptability to cloud, smoke, water - dropping, the buildings, the grounds and its shapes, good steady field, it has some technical defaults : lower resolution for location and measuring velocity, the more complex of its sending - receiving relay devices, weak anti - interference, the strict demand for the hole size in the line, the cleaner work environment and the higher cost

    毫米波具有最大的帶寬和最高的通信速率，但也有最高的成本要求和較難克服的技術問題，即傳播的多徑效應，降水、雲霧、地形、地貌、建築物等的反射散射，打雷時的嚴重干擾，設備復雜，維護困難等等；泄漏同軸電纜的帶寬目前已做到3ghz ，具有對地形地貌建築物的適應性強，場強穩定，但它的定位測速精度低，它的收發中繼設備較復雜，抗干擾能力低，電纜上的開槽有著嚴格的尺寸要求，工作環境要求清潔，成本較高；傳統無線感應技術具有結構簡單，成本低廉，維護方便，定位精度較高的優點，但是，它沒有抗干擾能力。
  5. By use of the morphological coefficients of estuarine riverbed and the relevant data of the north channel of the yangtze river estuary, the widening rate of the regulation line of the north deep - water channel of the yangtze river estuary is calculated, and the calculation result is in agreement with that of the fixed bed model test

    利用已有的河口河床形態系數及長江口北槽的有關數據，估算了長江口北槽深水航道治導線的放寬率，且與定床物理模型試驗值基本相符。
  6. Aimed at higher efficiency, stable and reliable operation and convenient supervisory, the project adopted a plc - ipc combined hybrid control system with the merits of flexible configuration, accurate measurement, coordinated control, reliable performance and convenient maintenance, achieving a higher automation level of material proportioning

    為了提高生產效率，保持穩定可靠運行，提供便利的監控手段，在改造工程中採用了plc和ipc相結合的混合控制系統方案，具有配置靈活、計量準確、控制協調、性能可靠和維修方便等優勢，使高爐槽下配料達到較高的自動化水平。
  7. After the various visual defects during drilling processes were analyzed, the importance of drilling with compressive pre stress was presented

    以加工效率為指標，通過正交試驗對鉆頭的磨料粒度、濃度、水槽數和壁厚等因素進行了優化分析，確定了適宜的刀具參數。
分享友人
分享到 Line

分享到臉書