玻璃絲結構 的英文怎麼說
中文拼音 [bōlísījiēgòu]
玻璃絲結構
英文
glass filament construction-
Through the experimental research, we think : the technological capacity of fiberglass asphalt macadam if weaker than asphalt macadam, however, if use elasticized capacity to solve blending technological problem. adjust the breed of fiber silk, extend its diameter, its paving capacity is still worth exploring, asphalt - rubber macadam structure lager have good deformed - become capacity and crazed - resistance capacity, small gap rate. good water - resistance capacity, good hot - stability and simple construction technology. therefore. pitch rubber spall is a good cover material which is suitable for the second class or lower whose asphalt pavement has split open because of fatigue. and is the good structural measure of preventing half - rigidity grass - roots unit shrink - rift reflecting. pave a thin layer of pitch rubber spall between asphalt - type pavement layer and half - rigidity basic level, although the cost of building is higher than paving togongbu in the middle, the construction technology, crazing - resistance and water - resistance are better than togongbu, not only could reduce greatly the reflex of half - rigidity grass - roots unit material, long then the use lifespan of pavement, but also it is possible to reduce suitably the thickness of asphalt mixture layer, though the cast of building in the early days becomes more, in the long - term opinion, it have fully important technological and economical significance
通過試驗研究認為：玻璃纖維瀝青碎石的技術性能不如瀝青碎石好，但路用彈性性能較好，如能解決拌和工藝問題，調整纖維絲的品種，增大其直徑，其路用性能仍值得探討，瀝青橡膠碎石結構層具有變形性能和抗裂性能良好，空隙率小，防水性能好，熱穩定性較好，施工工藝簡單的特點，因此，瀝青橡膠碎石是二級及二級以下公路因疲勞而開裂的瀝青路面的良好罩面材料，也是防止半剛性基層收縮裂縫反射的良好結構措施，在瀝青類路面面層和半剛性基層之間夾鋪瀝青橡膠碎石薄層，雖然造價比夾鋪土工布高，但其施工工藝，抗裂性能和防水性能均優于土工布，不僅可以大大減少半剛性基層材料的反射裂縫，延長路面使用壽命，而且可能適當減薄瀝青混合料面層的厚度，雖然初期造價有所增加，從長遠來看，具有十分重要的技術和經濟意義。This processing line is composed of two sszym 1500a straight line double pencil edgers, with 90transfer worktable. which adopts plc control system sets processing parameters via interface to control width and speed, double screw rod and double straight line glide transmission, guarantee the active briges parallel moving precision, can grind 3 8mm thickness flat edge and pencil edge. this machine structure was designed tightly, function stabilized with high efficiency. it is mainly suit for large batch industrial glass which does deep process and production, be matched with glue printing steel etc. production line. this product is a master work with firenew design by our company, it is another contributisn for chinese glass double edger series
採用plc控制系統通過界面設定參數，控制加工的寬度和速度，雙絲桿和雙直線導軌傳動，保證活動橋的平行移動精度，適用與加工3 8mm的小規格玻璃的平邊和圓邊。該機設計結構緊湊，性能穩定可靠，生產效率高。主要適應大批量工業玻璃深加工生產可以與夾膠印花鋼化等生產線配套使用。Aerospace - thermosetting epoxy woven glass filament fabric preimpregnated for structural applications - technical specification
航空航天.結構用熱固環氧樹脂紡織玻璃纖維長絲織物預
分享友人