球形壓力容器 的英文怎麼說

中文拼音 [qiúxíngyālìróngqì]
球形壓力容器 英文
spherical pressure vessel
  • 球 : 名詞1 （以半圓的直徑為軸 使半圓旋轉一周而成的立體; 由中心到表面各點距離都相等的立體） sphere; glo...
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 球形 : sphere; sphericity; spherical; globular; round球形安全閥 ball relief valve; 球形閥 globe valve;球...
  1. On the base of the basic structure study of the tooth - locked quick closure vessel of middle and low pressure with crown head, the optimization method of parameterized whole device is presented in this paper, the emphases of research is put on optimization of the tooth - locked quick closure device whose structure and load distribution is complicated, the wall of vessel, however, is designed according to the existing strength formula

    本文對帶有球冠形封頭的中、低壓齒嚙式快開容器的基本結構進行研究的基礎上，提出了齒嚙式快開容器的參數化整體優化方法，研究重點放在結構和受力復雜的齒嚙式快開裝置的優化，對于容器簡體壁厚仍採用現有強度公式設計。
  2. Stress measurement and analysis for a spherical vessel under hydrostatic test

    球形爆炸容器水壓試驗應力測試及分析
  3. In this paper, the metal explosive working technique and the fabrication characteristics of metal vessels with double layers were introduced. based on the comparison between new and traditional techniques, the reliability of the technique for mould - less high energy integral forming of spheroidal vessels with double layers was stated, and the prospective application of this techniques to the fabrication of the low temperature pressure vessels was presented

    本文將從前言、金屬爆炸加工技術介紹、雙層金屬容器加工製造要點、新技術與傳統技術的對比、無模高能整體分步成形雙層球型容器技術的可靠性和本技術在低溫壓力容器製造領域里應用的前景等六方面進行闡述。
  4. Unfired pressure vessels - requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

    非燃燒壓力容器.球形石墨鑄鐵制壓力容器和壓力零部件的設計和生產要求
  5. 16mnr and 45 # steel are taken as examples. the obtained results have been applied to analyze the safety of operation pressure and rationality of design of a kind of engineering structure - a flange joint of hemispherical head to cylindrical shell. try to seek a sort of new method to assessment the capability of structure to load beyond the traditional method which regards stress and strain as main parameters

    本文以45 ~ #調質鋼和壓力容器常用鋼材16mnr為研究對象，對金屬材料韌性斷裂的斷裂模式進行細觀機理上的研究，進而分析一種工程結構? ?採用與筒體厚度不同的半球形封頭的壓力容器的筒體連接結構? ?的靜載變形特點和破壞形式，嘗試在以應力應變為主要參數的傳統方法之外，尋求一種新的結構承載能力分析的方法。
  6. The stresses and strarns of cylindrical spherical and paraboloid shells can be solved when the drawing unsteadiness happen

    文中就圓柱殼形、圓球殼形、拋物線殼形封頭等壓力容器的失穩狀態，分別求出它們的應力和應變。
  7. In addition, the c language procedure for stress analysis calculate on connective structure between spherical head and cylindrical shell in jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a2 " strain and stress of basic parts " was adopted. therefore, the complicated process can be accomplished by computer

    此外，本文還對我國jb4732 - 1995 《鋼制壓力容器? ?分析設計標準》附錄a2 「基本部件的變形與應力分析」中有關球殼與柱殼連接邊緣的應力公式用c語言編制了計算程序，使復雜的計算過程完全可以由計算機來完成。
  8. Solve the problems that data jam, collecting data. etc. and work out a series of software accompanied to the testing system

    該軟體已用於對1000m ~ 3球形壓力容器進行球面任意三角形定位與數據分析。
分享友人
分享到 Line

分享到臉書