環圓剪 的英文怎麼說
中文拼音 [huányuánjiǎn]
環圓剪
英文
ring and circle shear-
The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing
由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。Standard test method for inplane shear properties of hoop wound polymer matrix composite cylinders
環形纏繞聚合母體復合圓柱體的表面剪切特性的標準試驗方法Saturated sand are testes in the laboratory under the undrained cyclic loading condition with static - dynamic dual purpose triaxial compression test apparatus, which is designed under the cooperation of hohai university and marui co. ltd japan. the results indicate that the stress path approaches from a initial stress point to the failure lines as cyclic loading goes on, and eventually converges on a certain limiting stress path in the vicinity of the failure lines. the stress - strain curve, however, does not converge on a closed hystersis loop ; the shear strain rapidly increases in looser sand or gradually and continually increases in denser sand
利用河海大學與日本圓井株式會社共同研製的新型的多功能靜動三軸儀進行了飽和砂土循環扭剪不排水試驗，研究表明，對于松砂，剪應變幅度快速地由微小增加到百分之幾甚至百分之十幾，對于緊砂，剪應變幅度逐漸地由微小增加到百分之幾甚至百分之十幾；經試驗初步研究表明用初始有效平均正應力歸一化的有效應力路徑很好的一致性。Punching tool parts, blocks for edm, scissor parts, circular knives, machine parts, extruding tools, tools for diecasting pulverized materials, pressure plates, sliding parts, valve parts, embossing dies, cutter disks, planer knives for machining of wood, hard metal tipped tools, rolls for cold rolling mills
沖壓工具零件、電火花機床的滑車、剪刀的刃口、環刀、機械零件、擠壓工具、硬模鑄造研磨材料的工具、承壓板、滑動零件、閥門零件、壓花模、圓盤刀、木工中刨刀、切削硬金屬刀片、冷壓滾軸。With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress
研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。When change the component of adhesive its shear strength increased from 39. 3 mpa to 53. 5 mpa at room temperature and it have long - term usage at 180 with 25 mpa and can be served at 230 in short period. the addition of liquid rubber resulted in a 300 % increase in the peeling strength. the addition of polymer ether imide led to a 260 % increase in the peeling strength, a 15 % increase in shear strength and a 10 increase in tg ( tg = 195. 54 )
研究結果表明： bmi dds e ? 51 tde ? 85組成的膠粘劑體系的室溫剪切強度為39 . 3mpa ，當改變環氧樹脂的含量時，剪切強度提高到53 . 5mpa ；用無規羧基液體丁腈橡膠改性環氧樹脂膠粘劑時室溫剝離強度提高3 . 0倍；用聚醚酰亞胺改性環氧樹脂膠粘劑，室溫剪切強度最高可達45 . 2mpa ，剝離強度提高2 . 6倍，玻璃化轉變溫度tg = 195 . 54 ，比未增韌體系提高10以上；碳纖維耐磨材料與同步器圓錐環的粘接實驗結果表明，膠粘劑的使用工藝性能良好，滿足室溫剪切強度30mpa和180剪切強度12 . 5mpa的技術要求。Annulus and toothed ring were arranged alternately, that is propitious to press, sheare and grind
圓環、齒環交替排列，更有利於對物料的沖擊、剪切及研磨。分享友人