環形滾軸 的英文怎麼說

中文拼音 [huánxínggǔnzhóu]
環形滾軸 英文
ring roller
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 環形 : annular; ringlike; ring form; bight; annularity環形癌 annular carcinoma; 環形電路 [訊] loop circu...
  1. Rolling bearings - needle roller bearings, drawn cup without inner rings - boundary dimensions and tolerances

    滾動軸承.拉制的杯形無內環滾針軸承.外形尺寸和公差
  2. Felt rings, felt strips, ring grooves for rolling bearing housings

    滾動軸承座用氈墊圈.氈帶和環形槽
  3. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  4. The bearing spot contact and the friction carries on after the analysis, has carried on the simulation to the bearing work process, from simply established sigin ball two race model to the complex distinction the roller conveyer, the single ball four roller conveyers and the circular roller conveyer single ball four roller conveyer steel wire roller conveyer ball bearing finite element models, introduced the modelling method in detail, the restraint and the load infliction method

    在點接觸和摩擦分析的基礎上，對軸承的工作過程進行了模擬，按由簡單到復雜的研究步驟，分別建立起了單球雙滾道，單球四滾道和圓環形滾道單球四滾道的鋼絲滾道球軸承有限元模型，解決了建模模擬過程中實體模型的建立，約束和載荷的施加等一系列問題。
  5. Ball bearings with spherical outside surfaces and extended inner ring width

    球形外表面和擴展內環寬度的滾珠軸承
  6. Rolling bearings - bearings with spherical outside surface and extended inner ring width - part 1 : insert bearings

    滾動軸承.帶球形外表面和增加內環寬度的軸承.第1部分
  7. Metric tapered roller bearings - specification for dimensions of flanged cups

    米制錐形滾柱軸承.第3部分:外環凸緣尺寸規范
  8. Rolling bearings. cylindrical roller bearings, separate thrust collars. boundary dimensions

    滾動軸承.柱型滾子軸承分離式推力環.外形尺寸
分享友人
分享到 Line

分享到臉書