生坯強度 的英文怎麼說
中文拼音 [shēngpīqiángdù]
生坯強度
英文
green strength-
Therefore, the purpose of this thesis is to look for a suitable preparing process for 3 - tcp with their micro - construction controlled more easily and the porosity rate and strength uniform. this paper created a new preparing method of porous ceramics, i. e. foam gel - casting technique, which integrated foam technique in porous ceramics preparing and gel - casting technique in structural ceramics preparing was applied to improve the preparing technique of porous p - tcp bioceramics in order to prepare ceramics bodies with high body intensity, controllable porosity and easily machining performance
因此，本論文努力尋求一種適合於- tcp多孔陶瓷的制備工藝，使其微觀結構易於調節控制，空隙率和強度達到平衡同一。在實驗中，結合了制備多孔陶瓷常用的發泡法和結構陶瓷制備中的注凝法，創新設計了一種新的多孔陶瓷成型方法? ?泡沫注凝法，對多孔- tcp生物陶瓷的成型工藝加以改進，制備出高強度、氣孔率可控以及易加工的陶瓷坯體。When heating temperature reached 300, crackings appeared on the surface of ceramic tiles but the microstructure of glaze exhibited no apparent change when heating temperature reached 900, the glaze melted, the crystal structure of the tiles broke down, the integrity of ceramic tile was destroyed and the intensity was almost lost
當溫度達到300 ，冷卻試驗時，釉面可產生裂紋，但顯微結構基本無變化；當溫度達到900 ，冷卻試驗時，釉面出現熔化現象，坯體晶體結構酥裂、破碎，完整性遭到破壞，強度基本喪失。Raw rubber or unvulcanized compounds. determination of green strength
生橡膠或硫化化合物.生坯強度測定Strength control of steel for cold rolling produced by thin slab continuous casting and rolling
薄板坯連鑄連軋線生產冷軋基板的強度控制Metallic powders - determination of green strength by transverse rupture of rectangular compacts
金屬粉末生坯強度的測定矩形壓坯橫向斷裂法X - ray diffraction analysis and density analysis and crystal structure analysis have been adopted to analyze the grid ’ s rough. through large numbers of experiments and practice, technological condition of gas discharge and depositional temperature and depositional pressure and depositional time of all kinds of the pyrolytic grid ’ s roughs has been gained. now we can deposit small and big grid ’ s roughs successfully
通過大量試驗研究和生產實踐，摸索並優化出不同品種規格的石墨柵極毛坯沉積的氣體流量、沉積溫度、沉積壓強、沉積時間等參數，能夠順利地沉積出性能優良的小型、大型的各類品種的石墨柵極毛坯，滿足了公司大功率及超大功率電子管的電參數要求，保證了新產品的成功開發。In the making process we use hot - forging warm - forging cold extrusion forming and magnetic annealing processes to completely solve the problem of complex form hign precision dimensions difficult manufacturing lower power and so on. what s more, part surface is very smooth with no trimmed margin, continuous flowing metal fiber, high strength, lower noise. forged claw poles obviously increase generator s power and life, and also improve finished product rate of roughness
在製造過程中採用了熱鍛溫鍛冷擠壓成型及磁性退火等先進生產工藝徹底解決了精鍛「爪極」形狀復雜尺寸精度高製造難度大功率低等問題，且產品表面光潔無飛邊金屬流動纖維連續毛坯強度大噪音低，明顯提高了發電機的功率和壽命，並且提高了毛坯成品率。The machine has low investment. it ' s safe and reliable, which avoiding the danger traditional blowing up mine brings. it has advantages such as reducing the processing waste, bringing down the intensity of labor to ensure safety in production, reducing noise and dust
機臺投資省安全可靠，避免使用爆破性的傳統開采方法，開採的坯料平整，減少加工廢料，降低勞動強度，保障安全生產，防止噪音及灰塵的污染。The technique can avoid produce ti / al chemical compound in high temperature. the chemical compound would increase the difficulty of pressing. the research on vacuum degassing and temperature of pressing can acquire the ideal composite powders of highly
對ti / al復合粉進行真空脫氣及低溫熱壓制可以降低坯料中空氣含量並提高粉末顆粒的界面結合強度，同時避免高溫下生成tial基化合物增加緻密難度，對真空脫氣及壓制溫度進行研究，獲得理想的緻密度極高的復合粉末。分享友人