疏塗層 的英文怎麼說

中文拼音 [shūtúcéng]
疏塗層 英文
open coat
  • 疏 : Ⅰ動詞1 （疏通） dredge （a river etc ）2 （疏忽） neglect 3 （分散; 使從密變稀） disperse; scatte...
  • 塗 : Ⅰ動詞1 （抹） spread on; apply; smear 2 （亂寫或亂畫） scrawl; scribble 3 （抹去） cross [blot; s...
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 塗層 : paint-coat; paintcoat; coat; coating; covering; lining; wrapping flux
  1. Development of super - hydrophobic transparent thin films

    超疏水性透明塗層的研究進展
  2. Progress in biomimicing of super - hydrophobic surface

    超疏水性塗層的研究進展
  3. Fabrication and super - hydrophobic characteristics of fluororesin silica sol composite coatings

    硅溶膠復合塗層的制備和超疏水性能研究
  4. Estrogen levels are high, there are more smear diversification cells, nuclear deep into dense ; low levels of estrogen, smear a small round or oval, blue - stained nuclear osteoporosis bottom of the cell

    雌激素水平高時，塗片中有較多角化細胞，核緻密深染；雌激素水平低時，塗片中出現小而圓或卵圓形，核疏鬆藍染的底層細胞。
  5. By investigating the influence of drying temperature, it was found that the optimum drying temperature is differ from the base material, such as the drying temperature of cu based film is 200, that of the glass based and aluminium based film is 240

    銅、玻璃基塗層的最佳乾燥溫度分別為200和240 ，該溫度下塗層形成微觀凹凸結構，疏水性高；添加成珠劑能增加塗層表面粗糙度，提高塗層疏水性能。
  6. Based on the technical requirements of manufacture, application and repair of the pump shell and cutter piece of the cutterhead pipeline dredge, put forward are the re - manufacture three principles on easily damaged workpieces of dredge engineering. with the inter - clamped structures on the pump liners, the gradient wear - resisting design on the cutter piece, and the new techniques in the process of re - manufacture, new wear - resistant materials, including high - cr alloy, overlaying and brazing deposits, and polymer adhesive coatings have been successfully applied to the re - manufacture dredge pump shell and cutter piece. the application results show that their wear - resistant lifetimes and the dredging profits have been increased remarkably

    根據絞吸挖泥船泥泵絞刀的製造、使用和修復性能要求，提出了疏浚工程易損件再製造三原則；採用泥泵內襯互鎖結構、絞刀梯度化耐磨設計和工藝再製造新技術，將高鉻合金耐磨材料、熔敷耐磨材料及其復合材料和高分子耐磨膠粘塗層材料成功地應用於再製造泥泵殼和絞刀片上，顯著提高了泥泵殼和絞刀的耐磨壽命和挖泥船的疏浚效益。
  7. The results show here, ( 1 ) the best reaction condition determined by the change of film properties in life time with uv light irradiation are : the hydrolyzation temperature is 60, the reaction time is 60 minutes, the less amount of water is of benefit to increase the hydrophobic property, the film formed with high degree polymer is steady

    研究結果如下： （ 1 ）通過調節反應參數，可制得性能優異的疏水性硅酮樹脂塗覆材料。最佳反應條件為：水解溫度60 、反應時間60min ；水解用水量較少和聚合度較大時樹脂塗層的性能較好。
分享友人
分享到 Line

分享到臉書