皮厚度計 的英文怎麼說
中文拼音 [píhòudùjì]
皮厚度計
英文
adipometer-
According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。The triceps skinfold ( tsf ) estimates the amount of body fat within 20 % and is therefore useful in determining the body ' s energy stores
三頭肌皮褶厚度（ tsf ）可以估計20 %之內的體脂，因此，在確定機體能量貯存方面很有用。Method to evaluate pile capacity precisely by using the coefficient of cleaning slime and coefficient of construction process and by controlling the total duration of construction is proposed herein after analyzing the influences of slime at pile bottom, thickness of mudcake by the side of pile, shape of hole wall, time of construction and construction process on the bearing capacity of large diameter cast - in - place pile
本文通過分析樁底沉渣、樁側泥皮厚度、孔壁形狀、成樁時間及施工工藝等對大口徑灌注樁承載力的影響，提出了在樁承載力計算中引入清底系數及成樁工藝系數，並控製成樁總時間以較準確地評價單樁承載力的方法。In connection with impact compaction technology of soil & stone cushion of third airstrip of pudong airport, it selects such experiment research as constructive technology & quality control, puts forward such constructive control parameters as pressing subsidence ratio ( single subsidence ratio ), pressing times, pseudo thickness and so on
摘要基於浦東機場三期跑道山皮石墊層採用沖擊壓實技術進行壓實的問題，選取試驗段進行了施工工藝及質量控制等試驗研究，提出了沖壓沉降率（分計沉降量） 、沖壓遍數、虛鋪厚度等施工控制參數。Monitoring the change will give us useful information about the sample. the paper begins from analyzing the principle of ecndt, studies the feasibility of the clearance detection between two metal plates using eddy current, furthermore makes experiment research
本文結合我國某飛機工業集團公司的《飛機蒙皮貼胎間隙檢查儀方案設計》研究項目，研究了渦流技術在多層金屬板厚度或板間間隙檢測的可行性，並進行實驗驗證。In upper level optimization, the thickness and geometry factors of composite skins and webs as well as other structural dimensions are taken as design variables. then, considering the behavior constraints and the side constraints, the structural mass is minimized by the mathematical programming technique. in lower level optimization, the mathematical programming technique or the genetic algorithm ( ga ) is used to search the practical stacking sequence of composite skins and webs to realize the given thickness and geometry factors from upper level optimization
底層優化設西北工業大學博士學位論文計以復合材料蒙皮和腹板等層合板各分層的厚度（或鋪層數） 、鋪層角和鋪層順序為設計變量，以層合板的幾何因子與頂層優化設計給出的最優幾何因子之間的誤差最小為目標，考慮層合板厚度和製造工藝性約束，採用數學規劃方法或遺傳演算法（ geneticalgorithm ，簡稱ga ）求出底層最優設計變量。The method also permits inverse design with flaps, specification of geometric constraints ( thickness, camber, etc. )
辦法還允許逆向設計皮瓣、幾何約束規格（厚度、拱等）分享友人