直出平行脈 的英文怎麼說

中文拼音 [zhíchūpínghángmài]
直出平行脈 英文
straight parallel veins
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 脈 : 脈名詞1. （動脈和靜脈的統稱） arteries and veins2. （脈搏的簡稱） pulse 3. （像血管的組織; 連貫成系統的東西） vein
  1. Therefore, a model of three sectors, respectively referring to domestic sector, manufacturing export sector and primary product export sector, has been established here to measure the technology spillover effects of export on domestic sector. finally, based on a broader framework, this dissertation went on to investigate the relationship between openness and china ' s economic growth, while the result shows that though there exists a notable dispute about how to measure the degree of china ' s openness, the index of trade dependence still maintains the better one to reflect china ' s economic openness. in the meanwhile, impulse response function ( irf ) method and forecasting errors variance decomposition ( fevd ) method, both of which are based on the vector auto - regression ( var ) system, are used here to investigate the dynamic relationship between openness and china ' s economic growth

    與傳統理論不同，新增長理論和新貿易理論都強調技術進步的作用，因此本文構建了一個三部門的技術外溢效應模型（國內部門、工業製成品出口部門以及初級產品出口部門） ，考察了工業製成品出口和初級產品出口對國內非出口部門不同的技術外溢效應；第四，從更加廣闊的視野就貿易開放度與中國經濟增長問題進行研究，有關貿易開放度如何度量一直是存在較大爭議的問題，本文首先對該類研究文獻進行了較為詳盡的述評，然後運用生產函數方法對所選取的5個貿易開放度度量指標進行了檢驗，結果發現盡管一些已有研究認為外貿依存度無法真實度量一國經濟開放水平，但是本文研究結果表明外貿依存度仍是度量我國貿易開放度的較好指標，進一步採用基於var系統的脈沖響應函數法以及預測誤差方法分解法對貿易開放促進經濟增長的作用進行了動態刻畫。
  2. Using the modified method, 6 kinds of tl topologies of single - switch converter are obtained. the deep research reveals that these tl topologies can have less value of the inductor by using interleaving modulation strategy compared with conventional modulation strategy on the condition that the current ripple of the inductor are the same. some drawbacks such as high voltage stress, difficulty of realizing soft - switching, and magnetic aberration were presented in the conventional push - pull converter

    對基本方法進行改進，提出了適合6種單管直流變換器的三電平拓撲變換方法，成功地得到了其三電平拓撲，開關管的電壓應力降為原來的一半；經過對這些三電平拓撲控制策略的深入研究，詳細論述了交錯開關方式可以最大幅度地減小電感的電流脈動，從而可以在電流脈動要求相同的情況下減小電感的設計值。
  3. The off - line program system based on cad / cam for dispensing robot is designed on the computer. in the module of trajectory planning, preliminary discussion is done about the shortest loop path and an algorithm of solving this problem is provided ; in the module of back procedure, dda ( digital differential analyzer ) is adopted in line, circle and ellipse interpolation. at last the protocol transferring program data to robot from off - line system is analyzed

    在離線編程的系統的設計中，實現了cad的建模、點膠軌跡的程序示教、工藝參數編輯、軌跡規劃、後置處理等功能，並在規劃模塊中針對平面內不規則排列點進行點膠的軌跡規劃進行了初步探討，採用圖論的方法，給出滿足實際要求且演算法復雜度較小的最短閉合迴路的程序演算法;在離線編程系統的後置處理模塊中，介紹了直線、圓弧、橢圓弧的dda插補方法以及脈沖分配不均勻的改進方法;最後對通信協議的制定進行了分析。
  4. Abstract : in this paper, the method of the impulse torques control is established for vertical planar two - link flexible manipulators on the basis of rigid manipulators control. the variables of two - link manipulators are restrained when the tip trajectory of manipulator is being tracked with this method. finally, the results of numerical emulation and experiment are shown in the paper

    文摘:在剛性雙連桿機械臂控制方案的基礎上，提出了柔性雙連桿機械臂的軌跡跟蹤和振動抑制的脈沖力矩控制方案，針對豎直平面雙連桿柔性機械臂進行了數值模擬和實驗研究。
分享友人
分享到 Line

分享到臉書