直接偏轉法 的英文怎麼說

中文拼音 [zhíjiēpiānzhuǎnfǎ]
直接偏轉法 英文
direct deflection ethod
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 偏 : Ⅰ形容詞1 （不正; 歪斜） inclined to one side; slanting; leaning 2 （只側重一面） partial; prejudi...
  • 轉 : 轉構詞成分。
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 直接 : direct; immediate
  1. However, df pre - processing is not required in a interferometer direction finder. it only makes use of the phase relations or differences of sensors disposed at different position. azimuth and elevation are caculated from the phase differences or displayed directly on a crt drived by the voltage or current from the phase differences

    干涉儀測向不必進行測向信號預處理而是直接或間接求取在空間上分開的傳感器上感應電勢之間的相位關系，即干涉相位差，方位角或仰角是直接由干涉相位差計算得到，或將兩基線正交的天線陣的干涉相位差轉化為驅動電壓（電流）分別加到crt陰極顯示器的垂直偏轉線圈和水平偏轉線圈，模擬顯示出來波方位，干涉儀測向為典型的相位測向方法。
  2. Prestack migration method, based on wave motion equation, is also developed for receiver function, and compared with ray method. both p - to - s conversion wave and direct p phase contained in receiver function are migrated and imaged by reverse - time migration for data gather including all receiver functions recorded in all seismological stations for one event, and imaging profile is finally obtained by stacking for all events

    本文還在接收函數射線反投影疊加成像的基礎上，提出了一種基於波動方程的接收函數疊前偏移成像方法，將同一事件接收函數中的轉換波和直達p波震相以各自的速度向深度方向逆時延拓成像，並通過不同慢度接收函數的疊加，得到最終的偏移成像結果。
  3. Abstract : in order to solve the double parameters enveloped in the geartooth flank generating, the complicated double parameter envelope is simplified to the generating process between work - piece and imaginary crown generating gear by means of mathematical transformation. the equation of the imaginary crown generating surface and the partial derivatives are deduced, so the differential geometric parameters of the generating surface can be obtained. by analyzing the generating motion between the imaginary crown generating gear and the work - piece, all the first to third order geometric parameters of the generated tooth flank at any given point can be calculated

    文摘:為了解決直接求解展成法加工中存在的復雜雙參數包絡問題時的困難，提出通過數學變換，將此包絡問題轉化為假想平面產形輪與工件之間的展成問題來進行研究.推導了假想產形面的方程和各階偏導矢，於是可獲得產形面的微分幾何參數.通過分析假想平面產形輪與工件之間的展成運動，即可得到被展成齒面上任意指定點的全部一至三階微分幾何參數
  4. Comparison by direct deflection method

    直接偏轉比較法
分享友人
分享到 Line

分享到臉書