直流電流計 的英文怎麼說

中文拼音 [zhíliúdiànliújì]
直流電流計 英文
dc ammeter
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 直流 : direct current （dc）; constant current; steady current; continuous current; zero frequency curre...
  • 電流 : current; galvanic current; electric current; electricity; current flow電流保護裝置 current protec...
  1. This paper is based on " the remodeled item of the 122mm automatic barbette servo system ". it introduced the controlled project of brushless direct current motor realized by dsp at first. on the base of analyzing and studying the driving wave of the brushless direct current motor thoroughly and fully, it carried on the servo system ' s simulink and presented the concrete software and hardware ' s devise of the whole system in the end

    本論文的撰寫是以「 122mm自行迫榴炮伺服控制系統的改型項目」為基礎，首先介紹了dsp實現無刷直流電機的控制方案，在深入、系統的分析和研究了無刷直流電機驅動波形的基礎上，然後進行了伺服控制系統的模擬，最後給出了伺服控制系統具體的軟硬體設計。
  2. Effective pole - arc coefficient determination of permanant magnet direct current motor

    永磁直流電機計算極弧系數的確定
  3. This paper presents the method of design and parameter optimizing in a phase - locked controller, which is used in high - speed brushless direct current motor ( bldcm ) speed control

    摘要提出一種用於高速無刷直流電動機鎖相速度控制器設計和參數優化方法。
  4. To giving some reference, this paper discusses the design of the instroduction, stirring up doubts, multimedia teaching and the content disposal about the emphacs and difficulty of the lessen of the base principle and structure of the dc motor

    摘要圍繞直流電機的基本工作原理與結構這節課的重點和難點，結合教學實踐，從導語設計、激疑教學、多媒體教學、教材內容處理等4個方面對其教學方法進行了討論，以期對教學同行提供借鑒。
  5. A novel low mechanical hysteretic ceramic capacitive pressure transducer has been made, by using of ceramic sealing technology ; integrate circuit ( ic ) technology and thick film plane fixing circuit technology. this transducer is made of a deformable ceramic diaphragm and a ceramic base plate, between which has an air cavum. a coaxial gold electrode was fired onto the diaphragm and the base plate

    本文利用新型陶瓷技術、集成電路技術和厚膜平面安裝電路技術，採用零力學滯后的陶瓷和陶瓷密封材料進行設計製造了一種非充液乾式的電容式壓力傳感器，該壓力傳感器由較厚的陶瓷基體和較薄的陶瓷膜片構成，中間形成一空氣介質腔，在基座和膜片之間內置同軸的雙電極，組成兩個電容，當膜片承受壓力時發生位移，使電容量產生變化，經後置處理電路直接轉換為可輸出的直流電壓信號。
  6. Be familiar with hv, mv and lv power distribution systems and power factor correction study & harmonic analysis, ups and dc power systems, power fiscal metering, and all necessary calculations to one project including short circuit calculation and protective device coordination study, lightning protection calculation, generator power calculation etc

    熟悉項目中的高、中、低壓配電系統和功率因素補償研究及諧波分析， ups和直流電氣系統，功率計量，相關計算（包括短路計算和保護裝置協調分析，照明保護計算，發電機功率計算等） 。
  7. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反電動勢類似正弦的準正弦波反電動勢無刷直流電動機，本文提出一種基於六個離散位置信號的自同步svpwm （電壓空間矢量法）控制方法，用以削弱電磁轉矩脈動，分析了實現這種方法的主要控制環節，包括起動時電壓空間矢量的初始定位，阻抗角與電流超前角的合理選擇以及連續轉子位置的估計等。
  8. In the paper, on the basis of research of static state and transient state in the scr and series connection valve circuit, the high voltage scr changing current valve device has been developed for ac - dc - ac high voltage commutatorless motor. the series connection valve circuit has been designed and simulated. the hardware design and software programming of trigger pulse system and monitoring system in the photo - electronic - photo fashion has been completed

    無換向器電動機在火電廠等工礦企業的電機調速節能領域中有十分廣闊的應用前景，本文在對晶閘管元件和串聯閥電路的靜態特性和動態特性研究的基礎上，研製了用於交直交電流型高壓無換向器電動機的高壓晶閘管換流閥裝置，進行了串聯閥電路的設計和模擬，完成了電光電方式的觸發脈沖系統和監測系統硬體設計及軟體編程，並進行了裝置的實驗調試。
  9. Digital signal processor ( dsp ) combined with repm bldcm, which build up a dc adjustable speed system, achieve to control multiple motor speed, positive and negative rotate, protect and fault exemine by a true single chip. design and present a electromagnetism scheme of repm bldcm used in electromotion chair drive system. select electronical components and chips in the drive board by contrast with variant drive mode. design the drive board principle picture, make a drive board pcb and debug it. design a principle picture with dsp core. workout the motor control code introduced popular programme modle. test the programme reliability and control performance by linking tms320lf2407 evm, pc, drive borad and the bldcm. the bldcm swatch is prepare experiment

    本論文闡述了方波驅動稀土永磁無刷直流電動機的原理及數學模型；設計並給出了一種電動座椅用稀土永磁無刷直流電動機的電磁設計方案；對電機採用何種驅動方式進行了對比分析；對驅動電路進行了元器件選型、原理圖設計、制板及調試；有針對性的闡述了dsp在本系統應用中所涉及到的功能模塊；設計了以dsp為核心的控制電路原理圖；以模塊化的軟體編程思想編制了電機控制軟體；通過tms320lf2407目標板、上位機、驅動板及電機的聯調，證明了系統可行。
  10. The dc power supply consists of passive filter circuit. the capacity of passive filter is up to 264mf

    設計的直流電源用最簡單的無源濾波電路，濾波電容的容量為264mf 。
  11. The method of compond target function variable weighting was adopted for solving compond target optimization problem, and compond target was put into single target

    在計算中，為達到無刷直流電動機全局優化的目的，採用隨機產生離散初始種群及隨機交叉操作和變異操作方法。
  12. A protective method based on voltage - frequency - converter and additional dc measuring the insulation between monitor wire and ground lines of hv double screen cable is developed and realized by analog and digital circuits

    通過分析6kv電纜絕緣監視保護的特點，提出了在高壓電纜監視線與接地線之間附加直流電源並利用v / f轉換實現監視保護的新方法，設計了相應的電路。
  13. In this paper, research and manufacture work on high efficiency high power density high - voltage high - power dc power is undertaken on the basis of basic theories and past production. by inquisition the basic theory and project of sreies - parallel resonant converter witch is a soft - switch converter was selected to outspread research and design work

    本文是在吸收前人研究成果的基礎上，理論聯系實際，針對高效、高功率密度、高壓大功率直流電源展開的研製工作。在經過大量的實際調研工作的基礎上，選擇了一種軟開關變換器（移相控制的串-並聯諧振變換器）的技術方案，並圍繞該方案展開理論研究和實際的設計工作。
  14. During the circuit design, the author analyzed the basic principle of the direct current motor, pwm control, h - bridge power driver, and two control techniques of h - bridge power drive circuit, designed its general structure, so the feasibility of the design is confirmed. then, reference, oscillator, power dmos gate drive circuit ( charge pump, bootstrap ), and dead time generation circuit are designed and analyzed in the sub - circuits. a current - controlled oscillator is presented in this thesis

    在電路設計中，作者介紹了直流電機的工作原理和數學模型、脈寬調制（ pwm ）控制原理、 h橋電路基本原理和h橋功率驅動電路的兩種控制模式，設計了驅動電路的總體結構，給出了電路的功能模塊，確定了設計的可行性，然後在子電路模塊中，重點分析設計了基準源電路、振蕩器電路、高端功率管柵驅動電路（電荷泵及自舉電路） 、低端功率管柵驅動電路和死區時間產生電路。
  15. A mathematic model of the motor is builded and emulated through matlab. the low - speed and constant - torque, high - speed and constant - power state is analyzed and researched, also the software approach of simulation to the driver has been done, a digital signal processor tms320lf2407 is developed successfully to control the perm square - wave bldcm driving airscrew of solar powered unmanned engine. it is useful to the further study

    在matlab下建立了電機的數學模型，通過計算機模擬，驗證了數學模型的正確性，同時在理論上對低速恆轉矩高速恆功率運行進行了分析與研究，提出了一種用模糊控制的方法實現恆功率控制，並對驅動器進行了系統模擬，成功的研製了以數字信號處理控制器tms320lf2407為控制核心的驅動器，控制無刷直流電動機驅動太陽能無人飛機的螺旋槳，為後面繼續研究工作提供了參考。
  16. This dissertation majorly researchs and designs full digital dc driving system with fuzzy control. it makes a scheme argumentation firstly, analyzing the pid algorithm and fuzzy control algorithm the ordinary digital pulse trigger algorithm and the double remainder method of pulse trigger in detail, and fuzzy control and the double remainder method are put forward to settle the under - mentioned problems, namely, the new viewpoint and the task having finished in this dissertation as follows : ( 1 ) in rder to overcome the influence of dc motor ' s parameter changing with time and nonlinear on the control system performance, this dissertation adopts fuzzy control as outside regulator and pi control as inside regulator in double regulators of the full digital dc motor driving system design ;. ( 2 ) aiming at the pulse trigger reliability of the ordinary d igital pulse trigger being low and leaking the pulse or the order of pulse confusion, this paper adopts the double remainder algorithm with short response time high pulse trigger reliability good adaptability and anti - jamming ; ( 3 ) this dissertation adopts tms320lf2407 which has good performance as major control chip this chip has power function with fast calculation capability, and accomplishes the software and hardware design in the dc motor driving system with fuzzy control ; ( 4 ) this dissertation also puts emphases on anti - jamming in hardware and software ; ( 5 ) after having designed the sample of full digital dc motor driving system with fuzzy control, a lot of experiments are performed to verify the performance and settles problems during experiment. the result of experiment proves the feasibility of design

    首先進行了方案論證，對模糊控制演算法和數字pid調節演算法、觸發脈沖的一般演算法和雙余演算法進行了詳細地研究分析，提出應用模糊控制和雙余法解決下述問題，即該論文主要的新見解和所完成的工作： （ 1 ）為了克服直流電機參數時變性和非線性因素對控制性能的影響，本設計中，雙閉環調速系統的外環採用模糊控制，內環採用pi控制，使系統在一定范圍內對直流電機參數變化和非線性因素影響有自適應能力； （ 2 ）針對常規數字觸發器演算法中觸發脈沖的可靠性不高，經常出現漏脈沖或是脈沖混亂的情況，本文採用雙余法，該演算法具有響應快，可靠性高，具有良好的適應性及抗干擾能力； （ 3 ）本設計中採用了速度快、功能強的tms320lf2407作為系統的主控晶元，應用該晶元完成系統的軟硬體設計： （ 4 ）本文對系統抗干擾的軟硬體措施進行了重點研究； （ 5 ）設計了具有模糊控制的全數字直流傳動系統原理樣機，並進行了試驗驗證，對試驗過程中出現的問題及時解決，最終實驗結果證明設計是可行的。
  17. Technical specification of map for d c resistance

    直流電阻計量保證方案技術規范
  18. The superior voltage stability of such a josephson voltage standard has many applications in dc voltage metrology

    此約瑟夫森電壓標準傑出的電壓穩定性在直流電壓計量中可以有許多應用。
  19. Design of digital - controlled direct current source

    數控直流電流源的設計
  20. Designed of a numerical - controlled and scanned direct current source

    數控與掃描直流電流源的設計
分享友人
分享到 Line

分享到臉書