直線定子電機 的英文怎麼說

中文拼音 [zhíxiàndìngzidiànjī]
直線定子電機 英文
linear stator machine
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 子 : 子Ⅰ名詞1 （兒子） son 2 （人的通稱） person 3 （古代特指有學問的男人） ancient title of respect f...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 機 : machineengine
  • 直線 : 1. （不彎曲的線） straight line2. （急劇的） steep; sharp
  • 電機 : （任何產生和應用電能的機器 特指發電機、電動機） any power generating or power driven machine esp ...
  1. The influences of stator ' s teeth on vibrating modal of the linear standing wave usm are discussed in this paper, in which eigenfrequency and wave - shape are analyzed while the position and geometry dimension of stator ' s teeth are changed, and it can give some advice on design for standing wave linear ultrasonic motor

    摘要本文對一類直線型駐波超聲電機振子的振動模態進行了系統的分析，討論了定子齒的位置、幾何尺寸對直線型超聲電機的固有頻率、振型的影響，為該類駐波型直線超聲電機的設計提供了理論依據。
  2. Design engineers now selecting pmbldc motors over conventional dc or induction motor drives for the following reasons : 1 ) the absence of brushes results in an essentially maintenance free operation and eliminates the undesirable effects of commutation such as sparks, brush - loss, radio - frequency interference, etc. 2 ) the low inertia of the rotor enhances the quality of the mechanical response of the motor, shortening the acceleration and deceleration time. 3 ) utilizing rare - earth permanent magnet materials with high coercive force results in substantially higher efficiency than their counterpart with brushes of the same size. 4 ) because of the absence of commutation segments, the stator construction is simple

    現在的工程師們更為青睞永磁無刷直流電動機是因為以下幾點原因： （ 1 ）去除了電刷的永磁無刷直流電動機徹底地免除了維護而且消除了我們不希望的由於換向帶來的火花、電刷損耗以及無線電干擾等等； （ 2 ）低轉動慣量的轉子提高了電機機械響應的質量，從而縮短了電機加速和減速的時間； （ 3 ）高矯頑力稀土永磁材料的使用使得同樣尺寸的永磁無刷直流電動機比傳統的直流電動機效率高； （ 4 ）由於沒有機械換向部分定子的結構簡單了。
  3. As a non - linear and multi - coupled system, the control of the ac induction motor ( acim ) has long been challenging. thanks to the vector control algorithm, acim can offer the same control capabilities and dynamic performance as traditional high - performance dc motors. with the vector control algorithm, the stator current of acim can be expressed in two orthogonal axes, and thus the rotor flux part and torque are de - coupled

    交流感應電機難于控制是因為它是一個非線性、多耦合的系統，矢量控制演算法通過坐標變換將異步電機的定子電流分解為轉子磁鏈方向和與之垂直方向的兩個分量分別進行控制，從而實現轉子磁通和轉矩的解耦，使得交流感應電機的動態性能可以和直流電機媲美。
  4. Motion control is a comprehensive subject. modern ac drive is a important embranchment in the field of motion control. however, it is difficult to rea1ize high - performance ac drive systems because induction motors are a kind of strongly - coupled nonlinear system with many variables and the torque is not easy to control. with vector control technology decoupling and torque control of ac motor are solved. the basic idea of vector control is that three - phase system is equiva1ent to two - phase system by coordinate transformation and it realizes the decoupling between field current and torque current of the stator in order to control the flux and current respectively, thus induction motor can be considered dc motor and high performance is achieved easily. with the progress of electric and electronic technology and the development of computer, high - integrated special modules and high - precision digital signal processor ( dsp ) are applied to ac drive so that vector control has been developed rapidly

    但是高性能的交流調速系統實現很困難，這是因為交流電機是多變量、強耦合的非線性系統，不易實現高性能轉矩控制。矢量控制技術則解決了交流電機解耦與轉矩控制問題，其基本思路? ?應用坐標變換將三相等效為二相，實現定子勵磁電流分量與轉矩電流分量之間的解耦，達到對交流電機磁鏈與電流分別控制的目的，交流電機等效為直流電機實現高性能調速。隨著電力電子技術的進步，計算機技術飛躍發展，高度集成的專用模塊和高精度的數字信號處理器應用於交流傳動系統中，促進矢量控制迅猛發展，日趨成熟。
  5. Based on the analytic analysis of the linear synchronous motor ’ s layered model, the paper deducted the composing of air gap magnetic fields and the analytic expression of levitating and advancing force. these results provide theoretic guidance not only for the analysis and measurement of the vehicle ’ s air - gap magnetic fields but also for the eatablishment of the

    採用各向異性介質近似模擬齒槽區域，並引入定子和轉子等效電流層的概念，建立了直線同步電機的磁場分層模型，在此基礎上得到了氣隙磁場的組成以及懸浮力和推力的解析表達式，為氣隙磁場的分析和測量以及列車運動情況下電磁力軟測量模型的建立提供了理論指導。
  6. Secondly, to achieve the independent regulation of active and reactive power output from the generator side which is designed for the purpose of tracing the maximum wind - energy capturing. the paper has analyzed the mathematic model of the ac excited doubly - fed machine and the stator field orientation control strategy of the motor as vscf wind power generator. thirdly, it has put forward and designed the dual pwm converter with the capacity of energy flowing bidirectional aimed at the demand of rotor energy bidirectional flow. the author constructed reliable and integrated experimental system and did a series of experimental study including no - load, cutting - in network and power generation at, below and above the synchronous speed

    論文首先分析了風機運行特性及其最佳風能利用原理，通過模擬及實驗驗證了採用直流電機的輸出特性模擬風力機的最大輸出功率曲線的可行性，並給出了模擬系統的硬體結構；然後為了實現交流勵磁發電機有功、無功功率獨立調節機理，分析了交流勵磁雙饋發電機的數學模型和在追蹤最大風能捕獲變速恆頻風力發電時必需的定子磁鏈定向矢量控制策略；針對雙饋發電機轉子能量雙向流動的要求，提出並設計了具有能量雙向流動能力的雙pwm交流勵磁用變頻器；最後為實現從理論到實踐的全面研究，研製出了一套小功率完整的雙pwm變頻器交流勵磁的雙饋風力發電機實驗系統，進行了空載、並網、同步速及上、下的發電運行等一系列的運行實驗；所完成的模擬和實驗研究均驗證了理論、模型和控制策略的正確性、可行性。
  7. The controllers have considered all sorts of imperceptible factors affecting the servo performances in a lpmsm servo system, which include the parametric uncertainties brought by the changes of the mobile mass, frictional coefficient, the thrust fluctuations aroused by the varieties of the magnetic density distributions and the time harmonic. the h state feedback controller restrains disturbances and uncertainties to keep the robust and stable performance. the ip controller, which has the ability of rapid response, is applied to satisfy the rapid performance

    在分析雙環控制問題時，針對直線永磁同步電動機，仔細考慮了能使伺服系統性能變壞的各種細微因素，如：永磁同步直線電機動子質量變化、摩擦系數變化等造成的模型參數不確定性，電機運行期間存在磁密分佈變化、時間諧波等產生的推力擾動等，採用了ip速度控制器和h _狀態反饋控制器相結合構成直線伺服的內環控制器，並輔助設計了外環的pi位置控制器。
  8. Specific issues examined are : compensation for the variation of the stator resistance, the offset error of the dc bus voltage, the voltage error generated by the forward voltage drop the dead time of the switches, improvement of the steady state performance, and the speed sensorless control for the pmsm dtc drive system are of major concern in this thesis

    定子電阻變化，直流母線電壓漂移，開關器件反向相電壓降、逆變器死區時間引起的電壓誤差的補償，提高系統穩態運行性能以及永磁同步電機直接轉矩控制的無速度傳感器運行方案等問題都是本文研究的重點。轉矩的快速響應是直接轉矩控制演算法的一個卓越的性能。
  9. As the rotor of the linear synchronous motor, the suspending electromagnetic irons are excited by rotor current and act with the long stator railway mutually. they have multiform functions such as suspending, advancing and generating electricity

    懸浮電磁鐵作為直線同步電機的次級，在繞組電流的激勵下，與長定子軌道相互作用，同時具備懸浮、推進、發電等多項功能。
  10. The power circuit of the system adopts the voltage frequency conversion structure of ac - dc - ac, and is composed of the commutation circuit, filter circuit and intelligence power module ( pm15rsh120 ). control circuit takes the dsp chip tms320lf2407 as core, including the pwm signal occurrence circuit, detect circuit of stator current and direct current voltage of generatrix, drive circuit of intelligence power module, detect circuit of speed, protect circuit of system etc. all of this builds the full digital vector control system of asynchronous motor

    該系統的功率電路採用電壓型的交-直-交變壓變頻結構，由整流電路、濾波電路及智能功率模塊ipm （ pm15rsh120 ）逆變電路構成;控制電路以dsp晶元tms320lf2407為核心，加上pwm信號發生電路、定子電流檢測電路、直流母線電壓檢測電路、智能功率模塊驅動電路、速度檢測電路、系統保護電路等，構成了功能齊全的異步電機全數字化矢量控制系統。
  11. In this paper, the development trend of micro - electronics equipment, the progress situation of precision work stage for laser photolithography equipment and the research and evolution of magnetic levitation technology in china and other countries are discussed generally. the main function, the demand of technical index and key technology of laser photolithography work stage are introduced simply. the magnetic levitation technology and the work principle of linear motor are stated, and the design and analysis method of mechatronics cad / cae for magnetic levitation precision stage is presented

    本文綜述了微電子製造設備發展趨勢及其精密工作臺如光刻機工作臺的國內外發展現狀及磁懸浮技術研究進展，簡要介紹了光刻機工作臺主要功能、技術指標要求、組成及關鍵技術，概述了磁懸浮技術及直線電機驅動的工作原理，著重研究用機電一體化cad cae集成技術設計、分析磁懸浮精密定位工作臺的方法，闡明了應用cad cae技術研製磁懸浮精密定位工作臺的現實意義。
  12. Propulsion theory and its structure character of maglev result in ' the special power supply mode for linear synchronous motor with long stators through power supply system

    磁懸浮列車的推進原理及其結構特點，導致了供電系統對直線同步電機長定子繞組的特殊的供電方式。
  13. Electromagnetic design of long stator linear synchronous motor used in mlv

    用於磁懸浮列車的長定子同步直線電動機的電磁設計
  14. An ems high - speed magnetic levitation vehicle is driven by long stator linear synchronous motor

    常導型高速磁浮列車採用長定子直線同步電機進行驅動。
  15. In the conventional pmsm dtc system, the stator flux linkage is calculated from the integration of the difference between the machine input voltage and voltage drop across the stator resistance, and the input voltage is obtained by synthesizing the dc - link voltage and the switching mode of the inverter

    在常規直接轉矩控制系統中，定子磁鏈是通過直接積分電機端部輸入電壓與定子電阻壓降之差計算得到的。電機端部的輸入電壓又是通過電機直流母線電壓和逆變器的開關狀態綜合得到的。
  16. Secondly, the beam orbit offset effects caused by the initial beam offset and the linac components " offsets have been quantitatively studied first. as an example with the injector linac for beijing electron positron collider upgrading project ( bepcii ), the beam orbit offset caused by the above error effects have been simulated and analyzed

    其次定量研究束流的初始徑向誤差和加速器部件的安裝誤差等對束流軌道偏軸的影響，並以北京正負電子對撞機二期工程（ bepc ）的直線加速器為例，給出了上述各種誤差導致軌道偏軸的模擬計算結果及其分析。
  17. Combining magnetic levitation technology and linear motor drive technology, applying cad / cae method, a new magnetic levitation precise stage is designed and researched, which is step and precise position mechanism in 1c chip manufacture equipment of micro - electronics trade such as laser photolithography equipment. it is an innovative research

    將磁懸浮技術和直線驅動技術相結合，採用cad cae技術手段設計研究了一種新型磁懸浮精密定位工作臺，它是針對微電子行業ic晶元製造設備如光刻機而研製的快速步進、精密定位機構，是創新性研究。
分享友人
分享到 Line

分享到臉書