直線步行試驗 的英文怎麼說

中文拼音 [zhíxiànbùhángshìyàn]
直線步行試驗 英文
straight line walking test
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 步 : Ⅰ名詞1 （步度; 腳步） pace; step 2 （階段） stage; step 3 （地步; 境地） condition; situation; st...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 直線 : 1. （不彎曲的線） straight line2. （急劇的） steep; sharp
  • 步行 : go on foot; walk步行鍛煉法 deambulation; 步行機 pedipulator; walking machine; walkie talkie; 步行...
  • 試驗 : trial; experiment; test
  1. In this thesis, studies are focused on as follows : ( 1 ) based on analyzing the general transfer - matrix, the conception of the generalized double layer soil model is proposed, and the transfer - matrix ( r ) of half - infinite elastic mass is introduce - d to the analytic expressions of stress and settlement under the uniform circular, rectangular and strip vertical loads in multi - layered soil ; ( 2 ) according to the analytic expressions of the additional stress and settlement under unifo - rm circular in multi - layered soil, rectangular and strip vertical loads, the programs are develop - ed to resolve and debugged. the results show that the programs are correct ; ( 3 ) through calculating the coefficient of additional stress on the central axis of uniform circ - ular vertical loads, under the corner point of the uniform rectangular vertical loads, and on the central axis of uniform strip vertical loads, and the settlement on the center of uniform circular vertical loads and uniform rectangular loads in double - layered soil, the characters of stress and settlement are discussed ; ( 4 ) a case, as an example, is studied with different calculation methods, such as traditional theory, fem. the results obtained are compared

    本文在已有研究成果的基礎上進一步開展了以下幾方面的研究： （ 1 ）在對層狀地基傳遞矩陣法中的總傳遞矩陣分析的基礎上，提出了廣義雙層地基模型的概念，並把半無限體的傳遞矩陣r引入到多層地基在圓形垂直均布荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式中； （ 2 ）根據多層地基在圓形荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式，編制了程序，調試通過並驗證了其正確性； （ 3 ）通過對雙層地基圓形垂直均布荷載中心軸線上的附加應力系數和荷載中心沉降，矩形垂直均布荷載角點下的附加應力系數和荷載角點沉降及條形垂直均布荷載中心軸線上的附加應力系數進行的計算，探討了雙層地基中的附加應力與沉降特性； （ 4 ）應用本文的層狀地基體系理論對一個工程實例進行了計算分析，並與傳統的計算方法的計算結果和有限單元方法的計算結果進行了對比分析，結果表明利用層狀地基理論計算更能反映地基中附加應力分佈的實際情況。
  2. The dissertation is mainly including four section : the first is the experiments done in the tank, which will supply the reliable information of imaging data ; the second is image edge detection by the use of the art of the zernkie moments, which is used to detect the liner and threaded edge of the object, the third is the underwater camera calibration technique, the forth is automatic positioning the location of the camera by used of the art of cross - ratio, the result of which is satisfied

    本文工作分為四個部分：第一部分是水槽實驗部分，它為后續的工作提供了可靠的圖像數據信息；第二部分是基於zom距的直線、曲線邊緣提取技術及相關的與處理技術；第三部分，水下攝像機標定技術研究，基於改進的tsai演算法，採用逐步分解的標定策略。並探討了一種相對簡單的、靈活的標定技術；第四部分是攝像機定位技術研究，採用具有平移不變性的交比進行攝像機定位，模擬試驗的最大誤差不超過2 ，效果還是令人滿意的。
  3. Upon existent theoretical and experimental results and based on a great of laboratory investigations carried out in chongqing university, for the first time this paper studies systematically the insulators dc discharge performance and flashover mechanism of iced insulators in the complex atmospheric environment, which will contribute to the understanding of flashover phenomena observed on ice surface at low air pressure and provide the test and theoretical reference for hv and ehv transmission lines design and safety service

    為此，在國內外現有工作的基礎上，通過大量的試驗研究，本文主要研究了復雜環境中絕緣子的直流閃絡特性及閃絡機理。其結果有助於進一步了解低氣壓下覆冰絕緣子的閃絡現象，並可為輸電線路的設計和安全運行提供理論依據。
  4. Abstract : in this paper, a kind of technological scheme for one - step precision forging spur gear with large module is put forward by using positive friction role. experiment, in which commercial pure lead is taken as test material, is done in the special die designed, and force vs. stroke curve is recorded. it is shown that positive friction role can efficiently make a contribution to the filling of the tooth cavity, but increase forming force

    文摘:針對大模數直齒圓柱齒輪，提出了利用積極摩擦一步成形的工藝方案，並用工業純鉛作為試驗材料，在設計的專用模具上進行試驗，記錄了力? ?行程曲線，結果表明：利用積極摩擦作用能夠有效地保證直齒圓柱齒輪精鍛時齒腔充滿，但同時增加了變形力。
分享友人
分享到 Line

分享到臉書