直線的傾角 的英文怎麼說

中文拼音 [zhíxiàndeqīngjiǎo]
直線的傾角 英文
inclination of a line
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 直線 : 1. （不彎曲的線） straight line2. （急劇的） steep; sharp
  1. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  2. First, this method decide the skew angle of a business card image according to four border fitting lines of the business card, then a method based on block move is provided to correct image and black border is erased based on position of border near - line

    該方法先檢測出名片的四條邊緣擬合直線，由四條邊緣擬合直線的傾斜角度來確定名片圖像傾斜角度，然後採用逐段整塊搬移的方法來對圖像進行傾斜校正，再根據邊緣擬合直線位置去除黑邊。
  3. The position and size of the monochromator, focusing curvature radii and tilting angles of the germanium focusing monochromator under different different take - off angle, size and divergency of the second collimator and intensity loss due to the use of it were determined. the neutron flux at different wavelength, under different reflection and take - off angle of the monochromator and divergency of the first collimator, were given. the simulation on the aperture used for limiting beam size in front of the sample showed that, smaller the size of the aperture and further the distance from the aperture to the sample, greater the loss of the intensity and more serious the spread of the beam along vertical direction at the sample position which makes the practical sampling volume greater than expected

    用蒙特卡羅模擬方法對中子應力衍射譜儀的設計方案進行了優化研究，提出了一系列可供參考的數據：確定了單色器的位置、尺寸、垂直聚焦單色器在不同起飛角下的聚焦曲率半徑和傾角；討論了第二準直器的尺寸和發散，以及使用第二準直器造成的強度損失；給出了在不同單色器反射面、起飛角、中子波長和第一準直器發散度的情況下樣品處的中子注量率，以及多種組合情況下譜儀的解析度曲線；對限束方孔的尺寸、距離樣品遠近對強度損失和測量中的影響做了深入研究。
  4. By doing single fracture drainage experiments, this paper has successfully presented the logarithm function relationship between ratio of drainage discharge through upward and plumb drainage hole and the ratio of their equivalent diameters. the drainage effect will be the best when the included angle between drainage hole and fracture surface is 21 ~ 36

    4 、通過單裂隙排水試驗，建立了傾斜孔和垂直孔的排水量之比與其交界線的等效直徑比之間的自然對數關系式，排水孔排水量基本隨其與裂隙面的交角減小而增大；對單組裂隙排水的初步分析表明，排水孔與裂隙面的夾角在21 ~ 36范圍內排水效果最佳。
  5. 2 ) through many numeral experiment, using the crack face ' s slant angle and azimuth angle as parameters, we found some relations between three - dimension fractal parameters and two - dimension fractal parameters in rock mass : ds = ( 1. 0 + 0. 031 ) * dl + ( 1. 0 + 0. 0395 ), ns = nl, v = 1. 5986 * ( 2 - dl ) - 3. 2935 * sin ( st ) + 3. 8263, and found a way to speculate three - dimension fractal parameters from two - dimension fractal parameters. lt is the foundation to describe the distribution laws of crack face in rock mass by the observing results through rock mass section crack, 3 ) this paper constructed the three - dimensional fractal emulation theoretical system and erected three - dimensional fractal emulation model about crack face in rock mass 4 ) a emulation system about crack face in rock mass is developed by vc + +, it includes the function to get section plane chart and section block chart from three - dimensional network chart automatically, and some of the emulation examples is given

    2 ）通過大量數值試驗，以巖體裂縫面的傾角與方位角為紐帶，分析得出了巖體裂縫面數量三維分形分佈參數和巖體裂縫跡線二維分形分佈參數的關系： d _ s = （ 1 . 0 0 . 031 ） * d _ l + 1 . 0 0 . 0395 ， n _ s = * n _ 1 ， = 1 . 5986 * （ 2 - d _ l ） - 3 . 2935 * sin （ st ） + 3 . 8263並提出了由二維分形幾何參數來推導三維分形幾何參數的方法。為通過巖體剖面裂縫直接觀測結果，描述巖體裂縫面分佈規律奠定了基礎。 3 ）本文構建了巖體裂縫面的三維模擬理論體系，建立了巖太原理二大學周眨d二研究生學位論文體裂縫面的三維分形模擬模型。
  6. Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied

    然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。
  7. In new state standard < < machining center testing items - accuracy testing > > [ refering to iso / dis10791 ], issued in 1999, the test of straightness accuracy has been changed. now it becomes more scientific and reasonable. in old state standard, the testing of straightness accuracy of kinetic part only focus on vertical and " horizontal plane, and it only includes two linear errors ; but in new state standard, we not only measure those two linear errors, but also measure the errors of pitching, deflecting, and inclining of the kinetic part, so it includes two linear errors and three angle errors

    1999年公布的國標《加工中心檢驗條件?精度檢驗》 （參照iso dis10791訂）中，直線度等項的檢測做了更為科學的實質性更改，坐標移動的直線度以由只檢測垂直面和水平面內的兩個平移線值誤差，改為用移動坐標方向之外的另兩個坐標的平移線值誤差和移動部件繞三個坐標軸的俯仰，偏擺和傾斜三個角值誤差綜合表徵。
  8. Plunge is the dip of a line.

    伏角：指直線的傾角。
  9. The angle or inclination of a line or surface that meets another at any angle but90 =

    斜角，斜面一直線或平面與另一（直線或平面）相交所成的除90外的任意角或傾角
  10. The phase error brought in baselines ' obliquity is analysed specially and the connection to phase difference and baselines ' obliquity is proposed

    著重分析了基線傾角的存在引起的相位誤差，經分析得出當傾角不為0時，相位函數不再是一條直線，誤差的大小與入射角有關。
分享友人
分享到 Line

分享到臉書