直線節距 的英文怎麼說
中文拼音 [zhíxiànjiéjù]
直線節距
英文
linearpitch-
The directrixes of the in former two transmissions are the loxodrome and the geodesic on the pitch cones, that of the latter is an equal - pitch line along the direction of straight generatrixes in the hyperboloid surface, also is the vertical trajectory of the straight generatrixes
前兩種傳動形式的準線分別為節錐面上的斜航線與測地線,後者的準線為單葉雙曲面上沿直母線方向的等螺距曲線,且為直母線族的正交軌線。He unbuttoned successively in reversed direction waistcoat, trousers, shirt and vest along the medial line of irregular incrispated black hair extending in triangular convergence from the pelvic basin over the circumference of the abdomen and umbilicular fossicle along the medial line of nodes to the intersection of the sixth pectoral vertebr aelig ;, thence produced both ways at right angles and terminating in circles described about two equidistant points, right and left, on the summits of the mammary prominences
然後又反過來自下而上地依次解開背心長褲襯衫和內衣紐扣。他那雙手的軌跡從參差不卷縮起皺的黑色體毛的中心線也就是自骨盆底到下腹部肚臍眼周圍那一簇簇體毛,又沿著節結的中心線進而延伸到第六胸脊椎的交叉點,從這里又向兩側叢生,構成直角形,在左右等距離的兩個點,即環繞乳頭頂端形成的三角形收斂圖形的中心線穿行。Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad
然後,本文在考慮材料、幾何和狀態三重非線性的基礎上,對該連接形式進行了全面的計算機模擬,主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比,各種設計方法之間的對比,以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量,拼接點與梁端之間的距離,梁和柱的翼緣、腹板厚度,柱的軸力,接觸面的摩擦系數,翼緣和腹板拼接板的厚度等因素的影響。Maximum diameter of the material to be wound or maximum pitch
線材最大卷繞直徑或最大節距Specification for fine pitch gears - involute spur and helical gears
小節距齒輪規范.第1部分:漸開線直齒和斜齒齒輪The experiments have tested the rigidity of connections that is the m curve of connections, researched two kinds of destruction modes of beam - to - column connections, analyzed stress of the plate and the influence of the member ' s plate thickness, the quantity of self - drilling screws, the diameter of self - drilling screws, the interval of self - drilling screws to the rigidity of connections
實驗針對連接節點的剛度即連接的m曲線進行了測試,並著重研究樑柱節點的兩種破壞模式,分析了板域的應力分佈以及構件的板厚、連接螺釘的數量、直徑以及螺釘間距對連接節點剛度的影響。3. again applying the idea of singular blending to case of surfaces, a nuat b - spline interpolating blending surface is constructed by a explicit means and maximum distance between the interpolating surface and singular bilinear patch can be adjusted by the blending parameter similar to the case of the curve above. furthermore, some singular elements such as edges 、 ruled surfaces and plane can be conveniently embedded in the interpolating blending surface
3 .將奇異混合思想應用到曲面插值上,提出了nuatb樣條曲面混合插值方法,該方法不僅給出了插值的顯格式,而且在插值曲面中可任意鑲嵌棱邊、直紋面或平面,利用混合因子,調節插值曲面與相應奇異雙線性曲面片之間的最大距離Identifying method research of gross error in bi - pitch measurement of straightness
直線度雙節距法測量中的粗差識別方法研究When the suspended point is moving on the line in a kind of way, the pendulum will depart from the balance position. in order to minimize the swing movement of pendulum and minimize the consumption of power, a linear regulator is created for the system. finally, a optimum feed back status of speed is made
當懸掛點以某種規律沿直線運動時,會出現擺錘偏離原太原理工大學碩士研究生畢業論文平衡位置的情況,為了使擺錘在給定時間內在懸掛點行走一定距離的過程中擺角最小且能耗最少,本文將系統構造成為線性調節器,最終得到了使懸掛點移動速度最優的狀態反饋量Two sections of stranding cage for 8 - bobbin and 16 - bobbin are respectively driven by separate dc motors. new concept planetary back - twist mechanism is adopted. stranding pitches are adjustable steplessly
8盤16盤二段絞籠單獨直流電機分段驅動,採用新概念的行星式退扭結構,絞線節距無級可調。分享友人