直角螺紋 的英文怎麼說

中文拼音 [zhíjiǎoluówén]
直角螺紋 英文
square thread
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  1. 5 fixed whorl protective tube of awl type a fixed whorl protective tube of awl type b

    5固定螺紋直角形保護管式a固定螺紋直角形保護管式b
  2. Aircraft bolts and nuts - nuts, hexagonal, slotted castellated, normal height, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h標準高度帶槽帶缺口普通六角螺母
  3. Aircraft bolts and nuts - nuts, hexagonal, slotted castellated, reduced height, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級h h或h .帶槽帶缺口減少高度帶鎖緊孔左旋普通六角螺母
  4. Self - locking, floating, right angle anchor nuts with mj thread

    Mj螺紋直角游動板自鎖螺母
  5. Based on ansys, this paper studies stress concentration on single notch of eight kinds of high strength bolts used in grid structure, obtaining their stress concentration coefficients, discussing the effect of ascending angle, bottom radius of screw thread and bolt - ball on stress concentration, introducing their effect coefficients of a1, a2, a3, putting forward the formulae of stress concentration coefficient

    本文以ansys有限元軟體為研究手段，針對網架螺栓球節點的8種螺栓規格進行單缺口應力集中分析，定量求得相應的應力集中系數k _ t ；論述了螺紋升角、螺紋牙根圓角半徑r及球栓直徑比d / d對k _ t的影響，並引入相應的影響系數_ 1 、 _ 2及_ 3 ，最終提出了應力集中系數k的計算公式。
  6. Aircraft bolts and nuts - nuts, hexagonal, plain, reduced height, reduced across flats, with locking holes, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h減少高度減少高度帶鎖緊孔左旋普通六角螺母
  7. Nuts, hexagonal, plain, reduced height, normal across flats, iso m or iso mj threads 4h5h or 5h tolerance class according to diameter

    Iso m或iso mj螺紋直徑4h5h或5h級公差減少高度標稱十字槽平頭六角頭普通螺母
  8. Male elbow for butt joints - body

    卡套式錐螺紋對接直角接頭體
  9. Aircraft bolts and nuts - nuts, hexagonal, palin, reduced height, normal across flats, with locking holes, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    航空用螺栓和螺母. iso m或iso mj螺紋直徑4h5h或5h級公差帶鎖緊孔減少高度標稱十字槽平六角頭普通螺母
  10. Male elbow for butt joints - assembly

    卡套式錐螺紋對接直角管接頭
  11. Flared type tube fittings - male elbow - assembly

    擴口式錐螺紋直角管接頭
  12. Flared type tube fittings - male elbow - body

    擴口式錐螺紋直角管接頭體
  13. Aircraft bolts and nuts - nuts, hexagonal, plain, reduced height, reduced across flats, iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h減少高度減少對邊普通六角螺母
  14. Aircraft bolts and nuts - nuts, hexagonal, plain, reduced height, reduced across flats, left - hand iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h減少高度左旋普通六角螺母
  15. Aircraft bolts and nuts - nuts, hexagonal, plain, reduced height, reduced across flats, with locking holes, left - hand iso m or iso mj threads, 4h5h or 5h tolerance class according to diameter

    飛機用螺栓和螺母. iso m或iso mj螺紋直徑公差等級4h5h或5h減少高度減少對邊帶鎖緊孔左旋普通六角螺母
分享友人
分享到 Line

分享到臉書