直通式爐 的英文怎麼說
中文拼音 [zhítōngshìlú]
直通式爐
英文
continuous passing furnace-
Abstract : the distribution of cooling air which is in the grille - brick of the inner combustion hot air stove has been simulated with three dimension turbulent mathematical model so as to find a method which is used to improve the distribution of cooling air in hot air stove. the influence of differential horizontal plates on the distribution of cooling air is discussed. the results show that original big circle round field of flow in the pillar - cavity is changed into full one - way field of flow and edges gas flow, at the same time, is increased by horizontal plates. there is a different function with horizontal plates and vertical plates. to make the uniform distribution of cooling air in the hot air stove, it is necessary that horizontal plates and vertical plates are used in a combined way
文摘:應用紊流三維數學模型模擬內燃式熱風爐內冷風在格子磚柱中的分佈，尋求改善其分佈的途徑.討論了加設不同布置的水平導流板對氣流分佈的影響.模擬結果表明，在支柱空腔內加設水平導流板改變了原有大迴旋流場，使迴旋流變成大面積的單向流.通過在支柱空腔內加設水平導流板可以發展邊緣氣流，這恰好與加設豎直導流板的作用相反，水平導流板和豎直導流板的結合使用有望實現冷風在格子磚柱中的均勻分佈After thermodynamic calculation on several operation conditions of the furnace, cold - state flow and resistance mensuration, the combustion of the tubular - furnace hearth was changed into swirl and addition of radiate cylinder and oxygen content detection minish 1. 25 surplus air to less than 1. 15, improving the combustion condition and convection and radiate heat transfer efficacy, resuling in reducing the waste - gas temperature 45, decreasing exhaust gas loss, and saving fuel by 6 %
摘要通過對加熱爐幾種工況進行熱力計算、冷態試驗的流場分佈及阻力測定和熱態試驗的爐膛溫度場分佈及管壁溫度等參數的測定，確定將管式加熱爐爐膛內直流燃燒改為旋流場燃燒和增加輻射筒，增設煙氣含氧量分析，可以將燃燒的過剩空氣系數從1 . 35減小到1 . 15以下，極好地改善爐膛內的燃燒狀況和對流輻射傳熱效果，從而降低排煙溫度45 ，減少加熱爐排煙損失，節約了煤氣量6 %以上。This product is extensive to used for all kinds of minerals, cement, fire - proof materials, aluminum soil the familiar anticipating, the emery, glass raw materials, mechanism building sand, stone materials, sand metallurgy of slag. it has the higher yield effect than other types, especially used to crush harder and causticity materials such as carborundum, emery, magnesium sand
Pcl直通沖擊式破碎機制砂機特別適用於製作建築砂石磨料，耐火材料，水泥石英砂鋼砂爐渣粉銅礦石鐵礦石金礦砂混凝土骨料瀝青骨料等多種硬脆物料的細碎與中碎，是高效，節能的碎石制砂設備。Furthermore, the growth and the study of self - organized quantum dots structures become more and more important recently, and the application of self - organization technique become wider and wider in this thesis, we address the theory of film growth and the growth technique firstly more, the ways and characteristics of surface detection are prescribed we mainly report the growth process, results and discuss of self - organized quantum dots structures in the a12o3 substrates by s - k mode using ecr - mocvd, in the espd - u device the growth art of ain epilayer which is the preliminary foundation of self - organized gan / ain quantum dots structures, including the substrate cleaning, nitridation, the growth of buffer and the growth of gan and ain epilayer, is discussed we deliberately compare the test result of rheed xrd and afm and achieved the optimalized condition of ain at last we have successfully realized the growth of ain which is much smooth and better crystal quality moreover, we grow the self - organized gan / ain quantum dots structure in s - k mode because the limits of the heater temperature, we can not grow the atom - smooth epilayer of ain until now so we could not grow better quantum dots which have small diameter and big density but the self - organized quantum dots structures with better quality will be realized successfully if the substrate temperature is increased the thesis study belong to my tutor subject of national nature science foundation ( 69976008 )
本論文主要論述了在espd - u裝置上，採用電子迴旋共振等離子體增強mocvd （ ecr - pamocvd ）方法，在藍寶石襯底上通過s - k模式自組裝生長gan aln量子點結構的生長工藝、結果及討論。而重點分析了自組裝生長量子點之前的aln外延層生長工藝，包括襯底清洗、氮化、緩沖層的生長和gan 、 aln外延層的生長；通過高能電子衍射、 x射線衍射和原子力顯微鏡測試，並且對這些測試結果進行了詳細的比較研究，得出了較優化的工藝條件，生長出了晶質較好、表面較平整的aln外延層；進而採用s - k模式自組裝生長了gan aln量子點結構。由於實驗裝置加熱爐溫度的限制，我們沒有能夠生長出原子級平滑的aln外延層表面，因而沒能夠生長出密度比較大和直徑比較小的量子點。Thermal and structure character of straight reheating furnace were analyzed in csp technological process. coupling with heat conduction differential equations of the thin slab and the furnace lining, the mathemat ical model of heat transfer is established in the long one dimension furnace by using zone method for making the model of radiant heat transfer. the effect of the moving velocity and kinds of the slab on temperature distribution in the furnace is discussed based upon the solutions to the mathematical model
通過分析csp工藝中直通式輥底加熱爐的熱工及結構特性，採用區域法建立爐內輻射換熱數學模型，與加熱爐內連鑄坯及爐襯的一維導熱方程相耦合，建立長一維直通式輥底加熱爐爐內傳熱數學模型.通過對數學模型的求解，研究分析了不同的薄板坯移動速度及鋼種對加熱爐爐內溫度分佈的影響Abstract : thermal and structure character of straight reheating furnace were analyzed in csp technological process. coupling with heat conduction differential equations of the thin slab and the furnace lining, the mathemat ical model of heat transfer is established in the long one dimension furnace by using zone method for making the model of radiant heat transfer. the effect of the moving velocity and kinds of the slab on temperature distribution in the furnace is discussed based upon the solutions to the mathematical model
文摘:通過分析csp工藝中直通式輥底加熱爐的熱工及結構特性，採用區域法建立爐內輻射換熱數學模型，與加熱爐內連鑄坯及爐襯的一維導熱方程相耦合，建立長一維直通式輥底加熱爐爐內傳熱數學模型.通過對數學模型的求解，研究分析了不同的薄板坯移動速度及鋼種對加熱爐爐內溫度分佈的影響Continuous passing furnace
直通式爐Straight - through boilor
直通式鍋爐分享友人