直齒輪 的英文怎麼說

中文拼音 [zhíchǐlún]
直齒輪 英文
spur gear
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Master gears for checking spur gears ; receiving arbors

    檢查圓柱直齒輪用的標準齒輪.安裝心軸
  2. Equivalent spur gear of the helical gear

    斜齒輪的當量直齒輪
  3. Pinion - type cutters for cylindrical gears ; disc - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用盤形齒輪銑刀
  4. Pinion - type cutters for cylindrical gears ; shank - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用帶柄齒輪刀具
  5. Pinion - type cutters for cylindrical gears ; extended hub gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用加大轂形齒輪刀具
  6. With the research in the paper succeeded it would be certain that the helical gear pump would replace the spur gear pump now widely existed in the market and also could replace the other type of hydraulic pump in some areas, which surely greatly decrease the cost of manufacture and advance the development of technology. the importance is undisputable

    本論文研究的斜齒嚙合式低脈動齒輪泵可代替現廣泛存於市場上的直齒輪泵，並能在很大程度和范圍內替代其它形式液壓泵的作用，這對于促進機械裝備的技術進步、降低機械裝備的製造成本具有十分重要的意義，其應用前景將十分廣闊。
  7. At first, on the base of the analysis of the mechanism of the helical gear pump, the paper try to find the relationship of the helical gear pump flow pulse with its corresponding parameters, give the solution of the problems brought by the replace of spur gear to lay the firm basis for the structural design of helical gear pump

    本論文在對齒輪泵工作原理和流量脈動機理分析的基礎上，首先探討了斜齒齒輪泵的輸出流量脈動與斜齒輪各結構參數之間的關系，以及由於斜齒輪替代直齒輪帶來的相關問題並提出解決辦法，為斜齒齒輪泵的結構設計奠定基礎。
  8. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  9. The software uses two entity configuration methods : extruding and simulating entity cutting in realizing three dimensional configuration, which successfully achieve three dimensional configuration of involute columnar vertical gear, involute columnar helical gear, standard vertical spline, archimedes worm and disco - cam

    軟體在三維造型功能實現上使用了拉伸和模擬實體切削兩種實體造型方法，成功地實現了漸開線圓柱直齒輪、漸開線圓柱斜齒輪、標準直齒條、阿基米德蝸桿和盤形凸輪的三維造型。
  10. System defects and causes of the numerical simulation of spur gear with warm extrusion

    圓柱直齒輪溫擠壓數值模擬系統缺陷及其成因
  11. Calculation of the normal side gear clearance of internal - engaging involute gear transmisson

    內嚙合漸開線直齒輪傳動法向齒側間隙計算
  12. The result presents, it is relatively useful for filling in the tooth cavity of big modulus 、 high thickness spur increase to increase suitability height mount piece, and the load of forging spur gears can be decreased by adding a mandrel, but unit area forging force does not cut down, and it has a little influence on filling in the tooth cavity

    結果顯示，增加適當高度的鑲件對大模數、高厚圓柱直齒輪齒腔填充比較有利，增加芯棒可以降低齒輪成形載荷，但單位面積的成形力並未減少，且對齒輪的填充性影響不大。
  13. Parameterized design of involute straight gear based on pro e

    的漸開線直齒輪參數化設計
  14. Two stage gear deceleration, duo - cone floating seal, combined carrier roller to facilitate service

    兩級直齒輪減速，浮動油封密封，鏈輪採用組合式，便於維修。
  15. Unit heads. multi spindle heads. simple straight toothed pinions

    組合機床動力頭.多軸頭.簡單的直齒輪
  16. Tooth profile design for and finite element analysis of asymmetrical involute spur gears

    非對稱漸開線直齒輪齒廓設計與有限元分析
  17. Taking into account thermal and non - newtonian effects of the lubricant, this paper has theoretically investigated elastohydrodynamic lubrication of involute spur gears, and achieved the pressure distribution, film shape, temperature distribution and the values of the friction coefficient and its varying law along the line of action of gear transmission

    本文在考慮了潤滑劑的熱效應和非牛頓效應后，對漸開線直齒輪的彈流潤滑問題進行了理論研究，獲得了齒輪傳動的壓力分佈、溫度分佈、油膜形狀和齒面摩擦系數的取值范圍及其沿齒輪傳動嚙合線的分佈規律。
  18. Modular units for machine tools. multispindle heads. simple straight - toothed pinions

    機床的模塊裝置.多軸頭.簡單直齒輪
  19. Modular units for machine tools. multispindle heads. offset boss straight - toothed pinions

    機床的模塊裝置.多軸頭.偏心輪轂直齒輪
  20. This paper discusses the shape optimization problem of 3 - d elastic contact objects in theory using bem, and analyses the real contact problem of bears and rolls

    本文以邊界元法作為應力分析工具，對三維彈性接觸物體的形狀優化問題進行了理論上的探討，並對直齒輪接觸問題、滾子接觸問題進行了實際分析。
分享友人
分享到 Line

分享到臉書