真氣流速度 的英文怎麼說

中文拼音 [zhēnqìliúsùdù]
真氣流速度 英文
true air speed
  • 真 : Ⅰ形容詞（真實） true; genuine; real Ⅱ副詞1 （的確; 實在） really; truly; indeed 2 （清楚確實） cl...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 真氣 : essential qi
  • 流速 : [機械工程] velocity of flow; strength; [水文] current velocity; current speed; flow rate流速管 pi...
  1. Numerical calculative simulation could factually reflect the dynamic characteristics of the whole equipment and inner flow and diathermancy of split - stirling crycooler. through the calculation, the velocity, temperature, pressure and other detailed information of airflow in any position inner the crycooler could be gained ; the distribution of each parameter could be confirmed and reasonable explanation for the experiment result could be made

    數值計算模擬能接近真實地反映分置式斯特林製冷機的整機和內部流動、傳熱的動態特性，通過計算可以得到製冷機內部任一位置的氣流流動的速度、溫度、壓力等詳細信息，確定各參數的分佈情況，並可以對實驗結果做出合理的解釋。
  2. Using jgp560c magnetron sputtering equipment, cu / ag film are deposited on cd1 - xznxte substrate by dc magnetron sputtering in order to get the influences of the main experiments parameters such as sputtering power, gas flow, vacuum air pressure, magnetoelectricity power and substrate temperature on deposition rate of film, discovered that dc sputtering power is the most key factor influencing the deposition rate

    在jgp560c型超高真空多功能磁控濺射鍍膜機上，採用直流磁控濺射法在cdznte晶體上制備出cu ag合金薄膜，揭示了氣體流量、直流濺射功率、勵磁電源功率、工作氣壓和襯底溫度等工藝參數對沉積速率的影響規律。結果表明濺射功率對沉積速率的影響最大，隨濺射功率的增大沉積速率快速增大。
  3. Vacuum technology. vapour vacuum pumps. measurement of the volume rate of flow pumping speed

    真空技術.蒸氣真空泵.體積流量泵的抽氣速度的測定
  4. And then simulations of gas - particle two phase plane wake and gas - particle two phase plane jet were carried out by using this model. after numerical simulations of the two flow fields were finished, series of analytical work was done. first, the distribution of time - averaged velocity, turbulence intensity was analyzed, and some of the simulation results were compared with those of the experiments ; the coherent structure of vortices in the near wall region of the plane wake flow were studied by describing the evolution of the eddy structures, including the forming, developing and shedding from the wall of the vortices in the near wall region ; the coherent structure of vortices in the whole field was also studied, such as the forming, developing, moving, pairing and merging of the eddies etc.

    在對上述兩種流動形態的二維大渦模擬研究中，首先全面地分析了氣相時均流場的速度、湍流強度的分佈規律以及氣相速度的脈動規律等並就部分數值模擬結果與實驗結果進行了對比研究；分析了平面尾跡流場中近壁處旋渦擬序結構，全面和逼真地反映了近壁處旋渦的生成、發展和脫落的規律；描述分析了平面尾跡流和平面射流的全場流動旋渦擬序結構，從整個流場的角度反映旋渦的生成、發展、運動以及旋渦之間相互配對、合併的作用規律等。
  5. This paper presents the effects of some features on the productivity of raw c60 materials, such as distance and approaching speed of electrodes, helium partial pressure and arc current etc. then we separate and purify the raw materials and obtain pure solid c60 of 99. 9 % and compare the purification efficiency and effect of different fluxion phase and fixed phase and discuss the effects of the experimental conditions, such as the depositing speed, the type of the substrate, the surface structure of the substrate and the temperature of the substrate. finally, we use xps, afm, ultraviolet, infrared and raman to analyze the component, structure and feature of the films qualitatively and quantitatively

    本文首先研究了氦氣分壓、弧電流大小、電極間距以及電極推進速度等實驗條件對制備c _ （ 60 ）粗品產率的影響；接著選用柱色譜法分離提純得到了純度大於99 . 9的c _ （ 60 ）固體，比較了不同流動相和固定相的提純效率和效果；然後採用自己改進后的真空鍍膜機，利用電阻式加熱蒸鍍方法，得到了純c _ （ 60 ）薄膜和不同摻雜比的銀摻雜薄膜；探討了沉積速率、襯底種類、襯底表面結構以及襯底溫度等實驗條件對薄膜結構的影響；最後通過xps ， afm ，紫外，紅外，拉曼對薄膜的成分、結構和特性作了定性和半定量分析。
分享友人
分享到 Line

分享到臉書