真空分離時間 的英文怎麼說

中文拼音 [zhēnkōngfēnlíshíjiān]
真空分離時間 英文
vacuum separation time
  • 真 : Ⅰ形容詞（真實） true; genuine; real Ⅱ副詞1 （的確; 實在） really; truly; indeed 2 （清楚確實） cl...
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 真空 : [物理學] vacuum; empty space; vacuo
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well

    液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。
  2. The membrane layer is formed by the vacuum forming technology. by controlling the weight and the ratio of long path of ceramics fiber, changing the operation factor reasonably of vacuum forming, we can obtain the ceramic fiber composite membrane layer, which has pore diameters of about 5 to about 30um, porosity i s 50 - 80 %, and tensile strength is about 4. 1to 18. 1mpa and thickness of membrane layer is 0. 5 - 2 mm, has the good thermal shock resistance and peal off

    膜層採用真空抽濾成型工藝，通過控制膜組分中陶瓷纖維長徑比、纖維加入量、成型時料漿濃度、成型壓力及成型時間等可以獲得膜孔徑5 ? 30 m 、氣孔率50 ? 80 、抗折強度4 . 3 ? 18mpa 、膜層厚度0 . 5 ? 2mm 、具有良好熱性能和耐剝離性能的陶瓷纖維復合微濾膜材料。
  3. Not only does it study the plasma characteristics of the arcing and after - arcing between contacts, but also its diffusion to outside of the contacts and its effect on the arc shield. for the first time, it proves the non - stability of the plasma diffusion of after - arcing by experiments

    同時，分析了燃弧和弧后觸頭間隙等離子體的特性，探討了它向觸頭間隙外的擴散及對屏蔽罩的作用效果，用實驗證明真空滅弧室弧后殘余等離子體消散的不穩定性。
分享友人
分享到 Line

分享到臉書