真空加熱乾燥 的英文怎麼說

中文拼音 [zhēnkōngjiārègānzào]
真空加熱乾燥 英文
vacuum and heating drying
  • 真 : Ⅰ形容詞（真實） true; genuine; real Ⅱ副詞1 （的確; 實在） really; truly; indeed 2 （清楚確實） cl...
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 乾 : Ⅰ名詞1. （八卦之一） qian, one of the eight diagrams2. （姓氏） a surname Ⅱ形容詞（舊時稱男性的） male
  • 燥 : Ⅰ形容詞（缺少水分） dry Ⅱ名詞[中醫] （病因） dryness
  • 真空 : [物理學] vacuum; empty space; vacuo
  • 乾燥 : arefaction
  1. On the basis of test results, the effects of operation parameters such as material thickness, heating temperature and pressure of drying chamber on vacuum freeze drying are discussed. aiming at decreasing drying time and reducing energy consumption, these parameters are optimized and optimization results agree well with actual results

    在三因素二次正交回歸試驗的結果分析的基礎上，利用降維分析方法探討了凍干厚度、加熱板溫度和系統的真空度對乾燥時間和乾燥能耗的影響，並對混合加熱條件下單位水分能耗和凍干生產率進行了優化分析。
  2. To simplity and improve the tedious technological process, a new process is proposed to integrate well the heating and drying with impregnation in a vacuum tank

    一體式的真空乾燥及真空壓力浸漬工藝將上述兩道工藝合二為一，在同一臺真空罐內進行一體式的加熱、真空乾燥和真空壓力浸漬。
  3. When a constant vacuum is maintained, increasing the temperature can also speed up the drying process

    當真空度恆定，提高加熱溫度，能加快乾燥速率。
  4. Increasing both vacuum and heating temperature will speed up drying process significantly

    既提高真空度，又提高加熱溫度，則大大加快乾燥速率。
  5. The main products includes various steam and electric heating reaction vessel, conduction oil, outer coil reaction vessel, polyester and resin completed equipments, vacuum reducing concentration tank, methanol and ethanol recovery tower, various corrugated stuffing, high effective membrane evaporator, new - type centrifugal drag membrane evaporator, vacuum rake dryer, condensing drum cut - off machine, shell - and - tube condenser,

    本廠主要產品有各類蒸氣電加熱反應鍋，導熱油外盤管反應鍋，聚脂樹脂全套設備，真空減壓濃縮罐，甲醇乙醇回收塔，各類波紋填料，高效薄膜蒸發器，新型離心刮板式薄膜蒸發器，真空耙式乾燥機，冷凝滾筒切片機，列管式冷凝器，螺旋板式換熱器，外循環蒸發器，鋁制槽車貯罐，乳化設備，高速剪切分散機，種子罐，發酵罐，多功能提取罐，並承接各類非標設備。
  6. The dried material is put into the middle of shell, mixing by the rake teeth and the material shaft works back and forth. the indirect heating, equal agitation of rake teeth and grinding of breaking stick makes water in material evaporation. under the effect of vacuum system, the water in the dried material and apparent water are discharged and the vapor water is discharged from outlet of vacuum pump passing dry dust collector, wet dust collector and condenser

    被乾燥物料從殼體上方正中間加入，在不斷正反轉動的耙的攪拌下，物料軸向來回走動，與殼體內壁接觸的表面不斷更新，受到蒸汽的間接加熱，耙的均勻攪拌，粉碎棒的粉碎，使物料內的水份氣化，在真空系統的作用下，使被乾燥物料內部水份和表面水份更有利的排出，氣化的水份經乾式除塵器濕式除塵器冷凝器，從真空泵出口處放空。
  7. The results indicate that drying thickness, radiant temperature and pressure of drying chamber are the most three significant factors. there ' s hardly any relationship between freezing rate and drying time, the sublimation drying time of slow freezing material is shorter than quick freezing one, but its desorption drying time is relatively longer, so the total drying time is approximately the same. the initial freezing temperature and freezing manner has little influence on vacuum freeze drying process

    試驗表明：凍干厚度、加熱板溫度、系統的真空度是最重要的三個過程參數；凍結速率對總凍干時間沒有影響，慢凍物料的升華乾燥時間要比快凍物料短，但慢凍的解析時間相對較長，兩者的總凍干時間相差很小；初始凍結溫度對凍干過程的影響可以忽略。
  8. Conventionally the power capacitors were manufactured the way their wound cores should be heated and dried in a vacuum drying vessel first, and the cores should be pressed into capacitor shells, then all the unfinished capacitors were put into a vacuum pressure tank for inpregnation

    摘要傳統的電力電容器的生產工藝是將芯體元件卷繞后，先在真空乾燥罐內進行加熱和真空乾燥，然後將芯體元件壓裝到電容器殼內，再在另一臺真空壓力浸漬罐內進行真空壓力浸漬。
  9. The so - called vacuum drying is heating & drying of the materials under vacuum conditions to which, vacuum pump is adopted for air - bleed and humidity suction thus speedy drying is reached

    真空乾燥，就是將被乾燥物料處于真空條件下，進行加熱乾燥，它是利用真空泵進行抽氣抽濕，加快了乾燥速度。
  10. Vacuum heating - drying mechanism for oil - immersed transformer

    油浸式變壓器真空乾燥加熱機理的分析
  11. Minimum heating time is over 50 % less than that of traditional vacuum drying oven

    最短加熱時間，與傳統真空乾燥箱相比加熱時間減少50 %以上。
  12. In this paper, the processing condition of freeze - drying snack dumpling was studied, and the parameters of cooling rate, material volume, vacuum, and temperature were determined based on drying time and recovery ratio of water absorption

    摘要通過試驗對速食水餃冷凍乾燥工藝條件進行了初步研究，並以乾燥時間和復水比為指標確定了冷凍乾燥工藝中的預凍速率、單位面積裝料量、乾燥室真空度、加熱板溫度等工藝參數。
分享友人
分享到 Line

分享到臉書