硅加工工藝 的英文怎麼說

中文拼音 [guījiāgōnggōngyì]
硅加工工藝 英文
silicon process technology
  • 硅 : 名詞[化學] silicon （14號元素符號 si）
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 藝 : Ⅰ名詞1 （技能; 技術） skill 2 （藝術） art 3 [書面語] （準則） norm; standard; criterion4 [書面語...
  1. Doped silicon and germanium are technologically the most important types of semiconducting material.

    添加硅和鍺在工藝上是半導體物質中最重要的類型。
  2. Abstract : by examining the technical processes of the cold - press dies on silicon - steel plates by metalloscope, the causes of cracks in the cold - press dies are analyzed, from which technical measures that are used to avoid cracking are derived

    文摘:通過對硅鋼片冷沖模各加工工藝的檢查和金相顯微觀察，分析了冷沖模產生裂紋的原因，並提出了防止裂紋產生的工藝措施。
  3. The silicon force sensor using bulk silicon process has lots of advantages such as batch producible, low cost, high precision, small driving force, high reliability, low power consuming, small dimension, light weight and quick response, etc. therefore, a scheme is proposed in this paper

    由於微機械工藝採用的技術多是半導體工業的硅表面工藝和體硅加工工藝，因此這種傳感器可以大批量製造，且具有低成本、高精度、低驅動、高可靠性、低功耗、佔用空間小、重量輕和響應速度快等優點。
  4. The results of the uni - factor experiments and perpendicular experiments show their best mechanic synthesizing craft as followed : nvp ( 10 % wt ), kh570 ( 20 % wt ), hema ( 70 % wt ), initiator ( 0. 2 % wt ), crosslinker ( 20 % wt ), reacting 20 hours under 80 c. the factors which influenced organic silicon modified pvp hydrogel soft contact lens material ' s swelling capabilities were researched, which included temperature, monomer content, ion concentration etc. the experiments showed the equation swelling content ewc improved with the increase of nw, droped with the increase of kh570 and ion concentration, improved then droped with the raise of temperature, and hydrogels got the least ewc at 45 c. experiment carried on todiscuss water dehydration mechanism of organic silicon modified pvp hydrogel soft contact lens materials, which showed dehydration process could be divided into evaporating stage and diffusing stage

    正交實驗結果表明， nvp ? hema ? kh570共聚物的機械性能最佳時，其合成工藝條件為： nvp用量10 （質量百分含量，下同） ， kh570用量20 ， hema用量70 ，引發劑aibn用量0 . 2 ，交聯劑nmba用量0 . 2 ，反應溫度為80 ，反應時間16h 。討論了單體配比、溶脹溫度、離子濃度等因素對有機硅改性pvp水凝膠軟接觸透鏡材料溶脹性能的影響。實驗得出：水凝膠材料的平衡溶脹度ewc隨單體nvp含量的增加而增大， ewc隨kh570用量的增加而減小，隨離子濃度的增大而略微降低，隨溶脹溫度的升高先稍微下降後有所提高， 45時平衡含水量最低。
  5. Thermal analysis of silicon micromachining based micro hotplates

    基於硅微加工工藝的微熱板傳熱分析
  6. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  7. Abstract : in this paper, the design of the sense organ of the silicon miniature inertial meter is presented. the approving structure of the sense organ is fulfilled by the fabrication techniques of laser processing and chemical etching, laser fibre optic vibration is used to test the vibration characteristic of the suspensi on beams

    文摘:設計了硅微型慣性加速度計的敏感頭並應用激光加工和化學蝕刻相結合的工藝方法製造得到了滿意的結構，應用激光光纖測振儀檢測了懸臂梁振動特性。
  8. In this paper, the design of the sense organ of the silicon miniature inertial meter is presented. the approving structure of the sense organ is fulfilled by the fabrication techniques of laser processing and chemical etching, laser fibre optic vibration is used to test the vibration characteristic of the suspensi on beams

    設計了硅微型慣性加速度計的敏感頭並應用激光加工和化學蝕刻相結合的工藝方法製造得到了滿意的結構，應用激光光纖測振儀檢測了懸臂梁振動特性。
  9. Physical state : this produce is made of natural silica sand by the advanced processes of water scrubbing and reelecetion. natural silica sand has the naturally founded grain shape and uniform particle size and takes on brown - white or off - white color

    物理狀態：本產品經天然硅砂水洗，重選等工藝加工而成，天然硅砂具有天然的滾圓粒形和均勻的粒度，呈褐白色或灰白色。
  10. Mems optical switch for optical communication is fabrication by silicon surface micromachining technology. surface micromachining technique, based on the standard cmos processes, in the other hand, offers greater flexibility for realizing free - space optical systems on a single chip

    Mems光開關是採用表面微細機械加工技術製作而成，硅表面微機械加工技術是以cmos集成電路工藝為基礎的，它可以靈活地把光開關集成在一塊矽片上。
  11. Because of its excellent properties, such as high strength, high module, wear resisting, and etc., sicp was added to ferroalloy as a reinforce phase. but the intrinsic difference between the bonds led to poor fabrication of the composites. in this paper, the effects of alloying, sintering, and heat - treatment on the properties and microstructures of sicp / ferroalloy - based composites were studied, : it was found that sic particles reacted with ferroalloy when sintered in 1100

    碳化硅因其高強度、高模量、耐熱、耐磨等優良性能而被作為顆粒增強體來制備鐵基復合材料，但因其共價鍵與鐵基體的金屬鍵之間的本質區別導致兩者復合困難，本文擬從基體合金化、燒結及熱處理工藝等方面對鐵合金基復合材料組織與性能的影響進行考察，具體內容如下：加入fe - cu - c基體中的sicp顆粒， 1100燒結時就已經開始發生分解，但反應不強烈，在顆粒表面鍍鎳可以延緩基顆粒與基體之間的反應。
  12. Limited to historical reasons, conventional paint drying methods for lpg bottle are all infrared ray heating, which has some advantages such as simple system, convenient operation and fast on - off, but it has some disadvantages such as higher energy cost and maintenance costs

    限於歷史原因，傳統鋼瓶烤漆工藝均採用遠紅外電加熱烤漆方法，其優點是系統簡單、操作方便和起停迅速。但其缺點也非常明顯，烤漆能耗費用較高，遠紅外電加熱硅板更新費用較多。
  13. The silicone and silicone emulsion, hydrophobic additive, were preparaed by the method of hydrolytic polymerization and emulsion polymerization, respectively. the technical factors and properties of the coating were optimized. the design mothod of the heat - insulated coating film was studied

    首先用硅氧烷水解聚合法和乳液聚合法制備了高效疏水性硅酮樹脂和有機硅乳液型疏水添加劑，並對制備工藝參數、性能進行了優化。
  14. Further more, silicon is advantageous as the material of industrial temperature sensors, since its fabrication and processing techniques are well known. a novel method that get a 10um - 20um layer of single - crystal silicon as the temperature sensitive material and design transmitted configuration is presented

    論文在理論分析單晶硅透射特性的基礎上，提出了以微細加工各向異性腐蝕深槽的工藝方法，獲得10um 20um的單晶硅感溫薄膜，並採用透射式傳感結構。
  15. The silicon micro - machining technology is used to fabricate the bi - layered silicon microcantilever resonators, the excitation of silicon micro - resonators is achieved using electro - thermal method via fabricating thermal excitation resistance on the silicon microcantilever beam

    利用硅微機械加工工藝製作了雙層結構硅微懸臂梁諧振器，通過在硅微懸臂樑上製作的熱激勵電阻，用電熱方法對硅微諧振器實現了激振。
  16. Polymer melt intercalation is a promising new way to fabricate polymer layered - silicate nanocomposite by using conventional polymer melt blending technology. this method is simple and does n ' t need any solvents, so it is convenient to be put into production

    熔融插層是應用傳統聚合物共混加工工藝制備聚合物基硅酸鹽粘土納米復合材料的一種新方法，這種方法不需要任何溶劑，工藝簡單，更易於工業化應用。
  17. This paper is one part of the uestc ’ s assignment ? ? “ the design and research of mimu ” 。 by the research for mems and the mems acceleration sensor, this assignment will finish a series of mimu system, which will be applied to the rocket and the missile guided system. this thesis mainly include following facets : research the mature mems processing technic at the present, develop a type of capacitive acceleration sensor which structure is simple and based on a set of new silicon bulk micromachining process

    本論文來自電子科技大學機械電子工程學院的課題「 mems慣性組合的設計與研究」 。該課題希望通過對mems技術和mems慣性傳感器的研究，研製和設計出一系列能夠應用於火箭和導彈制導的mimu系統。主要進行了一下工作:研究了目前較為成熟的mems加工工藝，提出了一種結構簡單，基於各向異性體硅微加工技術的電容式加速度傳感器。
  18. Formation of silicon pit and study on method of electrochemical micromachining of deep macropore array

    硅誘導坑形成及深孔列陣電化學微加工工藝方案的探討
  19. At first, the production of the research on the silicon micromachined acceleration sensors is analyzed home and abroad. the simple - structure, facility - process and low - cost piezoresistive accelerometers are used in the fuze to feel the circumstances of launch, which is under the request of the detection of the circumstances of the fuze

    文中首先分析了國內外硅微加速度傳感器研究所取得的成果，根據引信環境信息探測的要求確定了結構簡單、加工工藝相對容易、成本較低的壓阻式加速度傳感器作為引信發射環境識別的傳感器。
  20. By the study on the different structure and technics, a new structure of single side tfpm with convolute stator and inner magnet rotor is developed. the stator core is made by convoluted silicon steel tape. the stator manufacture does not need punching

    通過對各種電機的結構特點及其加工工藝的分析研究，提出了新型的橫向磁通永磁電機結構，定子鐵心採用硅鋼片卷繞結構，轉子採用內置式永磁體結構，給出了新結構加工的工藝方法。
分享友人
分享到 Line

分享到臉書