硬化速率系數 的英文怎麼說

中文拼音 [yìnghuàsùlǜxìshǔ]
硬化速率系數 英文
rate of hardening parameters
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 硬化 : 1 （變硬） harden; stiffen; stiffening; indurascent; ossification; cure; curing 2 [醫學] （組織變...
  • 速率 : speed; rate; tempo
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  2. It can also determine the fault spot and reason. this technology has been used in some technological fields and proved efficient. it has promoted the revolution of maintance system and the historial protection is replaced by preventive maintenance. with this technology, we can improve the reliability of machine and decrease the maintance fee. recently, reserch has pick up a fervent pace in the area of fault diagnosis of electrical machines. the paper simply analyzes the fault reason of electrical machines, stressly describes and explores the methods of condition monitoring and fault diagnosis such as partial discharge, stator current, rotating speed, vibration etc. fault prognosis is now include diagnostic feature, reason, spot. prodigious improvement in signal processing hardware and software has made this possible. primarily, these techniques depend on locating specific harmonic components of the fault. these harmonic components are usually diffirent for diffirent types of faults. automated tools such as fuzzy logic based system is also simply presented in the paper

    本文從絕緣結構的故障機理入手，以絕緣結構故障的典型特徵? ?局部放電為研究對象，重點討論局部放電的在線監測方法、適用場合併比較它們的優缺點；在分析籠型異步電機轉子斷條在線監測的定子電流監測方法后，根據其缺陷，本文探討了溫升不平衡法、希爾伯特變換數字濾波、小波包分析法的原理及優點；以電機軸承、氣隙偏心等故障為研究對象，通過對電機振動和轉速頻率的檢測，診斷電機的故障類型；本文的重點工作是將人工智慧技術中的模糊技術應用於電機的狀態監測和故障診斷中，力求使電機故障診斷更接近人工智慧化；最後，本文對電機狀態監測和故障診斷系統進行了硬體和軟體初步設計，為實現預測維修提供了有效的技術手段。
分享友人
分享到 Line

分享到臉書