硬焊條 的英文怎麼說
中文拼音 [yìnghàntiáo]
硬焊條
英文
borium-
Covered electrodes for manual metal arc welding - procedure for the deposition of weld metal - hardness tests
手工電弧焊用塗劑焊條.焊接金屬沉積方法.硬度試驗Carton package : net 20kg for each model electrode
硬紙盒包裝:凈重20kg對于各種規格電焊條The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine
實驗結果表明,經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h , ac或815 1h + 700 8h , ac熱處理后,焊接區組織過渡均勻,可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ,而在600拉伸時高於tc11合金,獲得強度、塑性、硬度均令人滿意的綜合性能,且是一條可行的工藝路線。The result shows that tempered martensite has apparent lath character when temper is between 740 ~ 780, and the hardness of welded joint is 264 ~ 237hv, which can get better performance of the welded joint the lath character of martensite in welded joint disappears, and the carbide in the tempered sorbite of the base metal will aggregate when temper temperature is above 780, and the hardness and plastic property will reduce obviously
結果表明,在740 ~ 780之間回火,焊縫硬度為264 ~ 237hv ,回火馬氏體板條特徵明顯,可以獲得優良的焊接接頭性能;回火溫度超過780 ,焊縫板條馬氏體特徵消失,母材回火索氏體中碳化物產生偏聚,硬度、塑性明顯降低。Testing of filler metals by means of weld metal specimens ; test piece for determining the hardness for surfacing
用焊縫金屬試樣進行焊條檢驗測定堆焊硬度的試樣Steel tubes. spigot or mixed connections made of steel or cast iron for capillary brazing or braze welding. dimensions. technical delivery conditions
鋼管.毛細管釬焊或硬焊用鋼或鑄鐵制套筒或混合接頭.尺寸.交貨技術條件Aerospace - brazed and high - temperature brazed metallic components - technical specifications
航空航天.硬焊及高溫釬焊的金屬結構構件.交貨技術條The main research of this article is about the digitalization of the controlling circuit. the controlling circuit use the combination of the mcu ( microcontroller ) and dsp ( digital signal processor ) to get control. the control system is programmed to meet the need of the requirement of the welding process of the basic welding method, such as mig, pulse mig and so on, with the same hardware
本文主要是研究控制電路的數字化,控制電路採用單片機( mcu ,即微控制器microcontroller )與dsp (數字信號處理器)相結合的雙機系統來進行控制,在硬體不變的條件下,通過編程使控制系統需滿足mig 、脈沖mig等基本焊接方法的焊接工藝要求。Milling, planing, impact and percussion. high toughness for medium wear resistance. well suitable for brazing
銑削、刨平、擠壓和沖擊操作。在中等磨損條件下具有高的韌性。很適合硬焊。分享友人