碳損耗 的英文怎麼說
中文拼音 [tànsǔnhào]
碳損耗
英文
carbon loss-
Standard test methods for carbon black - heating loss
碳黑加熱損耗的標準測試方法Abstract : experiments were made on a ultrasonic machining tool with work - piece adhered to ultrasonic transducer head, to machine micro - holes on hard and brittle materials such as soda glass and si, to study the effects of tool materials , work - piece materials , amplitude , machining load , slurry concentration , tool length and the size of work - piece on machining rate and wear ratio. in this experiment, the micro - tool was made through wedg
文摘:通過以wedg放電加工手段製作微細超聲加工用工具,在採用工件加振方式的微細超聲加工機上對碳酸玻璃、半導體硅等硬脆材料試件進行微孔加工的實驗,來探討在某一特定加工條件下工具材料、工件材料、工件的振幅、加工靜載荷、磨料懸浮液濃度、工具長度及工件尺寸等重要因素對加工速度、工具損耗率的影響,為微細超聲加工技術的實用化提供參考依據。Test method for oxidation mass loss of manufactured carbon and graphite materials in air
人造碳與石墨材料在空氣中的氧化質量損耗測定方法Rubber or plastic coated fabrics. determination of the loss of volatile matter by means of the activated charcol method applied to one single side
橡膠或塑料塗層織物.用於單側的活性碳charcol方法測定揮發材料的損耗32 ghz to 1. 91ghz. the complex permittivity peak of nanometer siox and two dielectric losses of cnts are discovered in our experiment which are different from properties of other nanometer materials. we should do the further research to reveal the truth
在本實驗的工作中發現與其它納米材料不同的現象,納米氧化硅的介電常數出現峰值,碳納米管有兩個介電損耗峰,建議以後的工作對其原因進行分析。Plastics - determination of loss of plasticizers - activated carbon method
塑料.增塑劑損耗的測定.活性碳法Plastics - determination of loss of plasticizers - activated carbon method iso 176 : 2005 ; german version en iso 176 : 2005
塑料.增塑劑損耗的測定.活性碳法Cls21 - i metallized polypropylene capacitors have low dissipation factor, stable capacitance, puny thermoguotiety. they can steadily work on logic control circuits & integral circuits and phase etc of instruments
型金屬化聚碳酸酯電容器損耗小,電容量穩定,溫度系數小,能穩定地工作在精密儀器、儀表的邏輯控制電路,積分電路等場合。Cls21 - ii metallized polypropylene capacitors have low dissipation factor, stable capacitance, puny thermoguotiety. they can steadily work on logic control circuits & integral circuits and phase etc of instruments
Ii型金屬化聚碳酸酯電容器損耗小,電容量穩定,溫度系數小,能穩定地工作在精密儀器、儀表的邏輯控制電路,積分電路等場合。Time setting function for electrode and working material to prevent carbon accumulated and electrode consumed
電極與工作物放電時之時間設定功能,可防積碳及防電極損耗。Experiments on the influence of optical fiber ’ s diameter, coating, plying direction and embedment numbers on mechanical properties of cfrp, and optical fiber ’ s light - loss were carried out to study compatible properties of fbgs embedded in cfrp
通過實驗討論埋入光纖與碳纖維復合材料的相容性,即光纖直徑、塗層、排布方向及光纖埋入體積對cfrp力學性能的影響, cfrp對埋入光纖光導損耗的影響。The result of research into electromagnetic beheaviours of polymeric magnets as follows : all of the two agents ( acrylic acid and polycarbonate ) can reduce effectively magnetic loss and dielectric loss, moreover, acrylic acid can increase the dielectric constant of the polymeric magnet at high frequency and microwave band. on the whole, the polymeric magnet modified by acrylic acid is preferable. the research of ir spectrum and xps of the polymeric magnets have showed that modifying polymeric magnet with acrylic acid is a chemical method in the part of composing polymer, we have chosen ferrocene as raw stuff
對改性前後高分子磁體的電磁性能研究結果表明:用丙烯酸或聚碳酸酯對高分子磁體進行表面改性,兩種試劑均不影響高分子的磁導率,並且它們均有效地降低了高分子磁體的磁損耗和介電損耗,更有研究意義的足:丙烯酸使高分子磁體在高頻微波下的介電常數得到明顯提高:從總的方面來說,丙烯酸改性高分子磁體優于用聚碳酸酯改性的高分子磁體。分享友人