碳當量系數 的英文怎麼說
中文拼音 [tàndāngliángxìshǔ]
碳當量系數
英文
coefficient of carbon equivalent-
When an oxidizing plasma is run in a system coated with fluorocarbon film, a substantial quantity of f atoms is released in the plasma.
當氧氣等離子體在覆蓋有氟碳薄膜的系統中起輝時，就會有相當數量的F原子在等離子體中釋放。We also studied the dynamic characteristics of cf / cu ( c ) - cu composites, the results show that, by the method of graphite is coated with copper, the coefficient of friction and the wear rates remarkably decreased. with the increase of the copper coated carbon fiber content, the wear rates of cf / cu ( c ) - cu composites is notably decreased, while the coefficient of friction is increased. with the increase of electric current density, the wear rate of cf / cu ( c ) - cu composites is increased
研究發現，碳纖維鍍銅石墨-銅復合材料的電摩擦磨損性能與碳纖維含量存在一最佳值，當碳纖維含量為0 . 6時，其電摩擦磨損性能最好；對于不同電流密度下的電磨損性能的比較可以發現，通電磨損時的電摩擦系數要小於機械磨損時的摩擦系數，碳纖維鍍銅石墨-銅復合材料的電摩擦系數隨電流密度增大先減小而後增大，在電流密度為15a cm ~ 2時達到最小值；通電磨損量要遠大於機械磨損量，且隨著電流密度增大，磨損量增加。The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。In the shock tube, the detonation parameters, such as critical initiation energy, detonation velocity, detonation pressure, detonation limitation and etc., have been measured and the relation is too obtained between detonation parameters and equivalence ratio. chemical kinetics process of hydrocarbon fuel has been analyzed according to the chain reaction mechanism
在立式激波管中測試了工業燃料c _ 5h _ （ 8 . 68 ）的臨界起爆能、爆速、爆壓、爆轟極限，得到了爆轟參數與當量比之間的關系；從爆轟反應是一個鏈反應機理出發，分析碳氫燃料的反應動力學過程。When an oxidizing plasma is run in a system coated with fluorocarbon film, a substantial quantity of f atoms is released in the plasma
當氧氣等離子體在覆蓋有氟碳薄膜的系統中起輝時，就會有相當數量的f原子在等離子體中釋放。分享友人