磁帶繪圖系統 的英文怎麼說

中文拼音 [cídàihuìtúxìtǒng]
磁帶繪圖系統 英文
magnetic tape plotting system
  • 磁 : 名詞1. [物理學] （磁性; 能吸引鐵、鎳等的性質） magnetism 2. （瓷） porcelain; china
  • 繪 : 動詞（畫出圖形; 描寫） paint; draw
  • 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 磁帶 : （magnetic） tape; storage tape; magnetic band; magnetic belt
  • 繪圖 : plot; draw; sketch; plotting; mapping繪圖板 drawing board; field plotter; plotting board; plottin...
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. At present, the most of vtr which are used in watch - control occasion for speciality are short of a uniform control - check - alarm system, which brings on the discommodiousness of operation and the user can not know the time of occurring a fault, which reduces the reliability of the watch - control system. therefor, at first, i carefully analyze the servo theory of the vtr which had been produced by chmavc with k mechanism to find out the work rule of the control signal ; second, take out some right control signal ; then for dealing with the problem of vtr in use for watch - control, i choose some right components to design the uniform control system for many special vtr with protel software. it mainly includes the following functions : operation functions of all vtr ( for example : power, play, ff, rew, stop, rec, eject, fwd, rwd, sp, lp ) was controlled by line at the same time ; in, the process of recording, when the tape walks to the end or stops by itself, the system gives an alarm and shows the number of the wrong vtr ; in the process of recording, the system gives an alarm and shows the number of the wrong vtr when the video signal from vidicon is losed ; the system controls all vtr to record on the non - working time when there is something wrong in the guarding section ; the system controls the video from vtr to switch to right monitor

    目前，用在監控場合的業務用錄像機普遍缺乏一個統一的控制及檢測報警系統，這就導致了操作的不方便和出現了故障用戶不知道，降低了監控系統的可靠性，為此，我首先對華錄松下生產的k機芯的錄像機伺服原理進行仔細分析，找出各個伺服控制信號的控制變化規律；然後從中選出合適的控制信號；針對目前錄像機在實際監控使用過程中存在的問題，選用合適的元器件；運用protel繪圖軟體，設計了這個多臺業務用錄像機的統一控制系統，她主要包括以下功能：錄像機操作功能（如power play ff rew stop rec eject及正尋反尋帶速設定等）的統一線控控制功能；磁帶在記錄過程中，磁帶到頭和磁帶自己「偷停」的報警，並要能顯示出具體是哪一臺錄像機；在記錄狀態下，攝像頭輸入信號丟失報警，並要能顯示出具體是哪一臺錄像機；在休息或其他不需要記錄時，一旦警戒區有情況，則控制所有機器自動進入錄像狀態的功能；從錄像機輸出的監控圖像信號對監視器的切換功能。
  2. The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing

    本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。
  3. Plotting system, magnetic - tape

    磁帶繪圖系統
分享友人
分享到 Line

分享到臉書