磨擦試驗臺 的英文怎麼說

中文拼音 [mócāshìyàntái]
磨擦試驗臺 英文
reibprüfstand friction test stand
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 臺 : 臺名詞（指臺州） short for taizhou （in zhejiang province）
  • 磨擦 : rub; abrade; abrase磨擦電 triboelectricity; 磨擦工 rubber; 磨擦劑 abrasive; 磨擦器 grater; rubber...
  • 試驗 : trial; experiment; test
  1. The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine

    用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。
  2. The characteristics and shortcomings of high temperature sliding wear testing machine for roll materials in china and a broad were analyzed in this paper

    摘要文章分析了國內外軋輥材料高溫摩擦磨損試驗機的特點及其存在的不足，在此基礎上，研製開發了一臺材料高溫滑動磨損與熱接觸疲勞試驗機，並進行了初步的實驗。
  3. Bench test method for frictional characteristics of sintered metal friction materials run in lubricants

    濕式燒結金屬磨擦材料磨擦性能試驗臺試驗方法
  4. Based on an experiment performed on the piston ring - cylinder bore wear tester, liquid - solid lubrication is investigated in this thesis. the wear of the samples under different lubrication conditions ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight ) are discussed. the variations of the surface topography, especially the statistical parameters and functional parameters are studied, and the reasons that cause the variations are analysed

    本研究基於活塞環-缸套摩擦磨損臺架實驗研究了液-固二相流體潤滑的問題，探討了潤滑油中不含固體顆粒、含有0 . 02和0 . 1納米顆粒三種潤滑狀態下的磨損情況，並進一步研究了液-固二相流體潤滑狀態下試件表面形貌特性的變化，主要是統計參數和功能參數的變化，並探討了引起變化的原因，為更深入的液-固二相流體潤滑問題的研究以及表面形貌設計提供理論上的參考。
分享友人
分享到 Line

分享到臉書