磨機轉速 的英文怎麼說

中文拼音 [mójīzhuǎnsù]
磨機轉速 英文
mill speed
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 機 : machineengine
  • 轉 : 轉構詞成分。
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 轉速 : speed; revolution; rotation rate; speed of revolution; rotating speed; rotational speed轉速指示器...
  1. Automatic grinder with pneumatic carriage advance, with multiple angles seat housing knifes. 3 types of grinder wheels. 1 corindon coup bell norton, 1 corindon for vee gouges hss one vee borazon diamond for tantung vee gouges. motor 1. 5 kw at 2800 rpm. net weight make yourselve profesional sharpening, forget about outside vendors

    全自動氣壓控制調節，可以一次性同時磨兩把刀具，隨機可配備3種磨刀石. 1杯型磨具， 1個磨高速鋼刀用磨刀石， 1個磨鎢鋼刀用的金鋼石磨刀具.馬達為1 . 5千瓦，轉速可達2800rpm .凈重為85公斤.可移動式工作臺，針對所有專業刀具均可加工
  2. The magnetic suspension bearingless motors generate both electromagnetic torque and magnetic levitation forces for the rotor suspension by the motor itself. the bearingless motor is comparatively suited for using as artificial heart blood pump motor due to the advantages of without mechanical wear and noise, structure compact and contactless

    磁懸浮無軸承電機定、轉子既用於產生驅動力矩，同時又用於產生支撐轉子的磁懸浮力，具有無機械磨損、噪音小、可高轉速和體積小等特點，比較適用於人工心臟血泵電機。
  3. A research on theoretical rotative speed in ball mill and the optimum rotative speed in work

    球磨機理論轉速的研究和最佳工作轉速的探討
  4. The big dipper colloid mill principle of work full sound of something astir grinding pan tooth profile incline relative motion but becomes, high speed revolves, another static causes the material to receive the enormous shearing force and the friction force through tooth profile incline between material, at the same time and so on under the complex strength function causes the material for the fluid ultramicron smashing, the emulsification, the disperser, isotropically at the high frequency vibration and the high speed whirlpool, to stir and so on the function, may replace and surpass the stone mill, the sand blast machine, the ball mill, the breast is uniform machine, cuts the mulser, three rollers machine, organizes working efficiency and so on the stamp mill

    七星膠體磨工作原理充分動靜磨盤齒形斜面的相對運動而成，其中一個高速旋轉，另一個靜止使物料通過齒形斜面之間的物料受到極大的剪切力和摩擦力，同時又在高頻震動和高速旋渦等復雜力的作用下使物料為流體超微粒粉碎、乳化、分散、均質、攪拌等功能，可代替並優于石磨，砂磨機、球磨機、乳勻機、剪切乳化機、三輥機、組織搗碎機等工作效率。
  5. Seven stars colloid mill principle of work full sound of something astir grinding pan tooth profile incline relative motion but becomes, high speed revolves, another static causes the material to receive the enormous shearing force and the friction force through tooth profile incline between material, at the same time and so on under the complex strength function causes the material for the fluid ultramicron smashing, the emulsification, the disperser, isotropically at the high frequency vibration and the high speed whirlpool, to stir and so on the function, may replace and surpass the stone mill, the sand blast machine, the ball mill, the breast is uniform machine, cuts the mulser, three rollers machine, organizes working efficiency and so on the stamp mill

    七星膠體磨工作原理充分動靜磨盤齒形斜面的相對運動而成，其中一個高速旋轉，另一個靜止使物料通過齒形斜面之間的物料受到極大的剪切力和摩擦力，同時又在高頻震動和高速旋渦等復雜力的作用下使物料為流體超微粒粉碎、乳化、分散、均質、攪拌、混合等多種功能，可代替並優于石磨，砂磨機、球磨機、乳勻機、剪切乳化機、三輥機、組織搗碎機等工作效率。
  6. Automatic grinder for bell coup cutters for shaping lathes type bacci motor 0. 75 kw. with motoreducer with neumatic turbine at 18. 000 rpm micrometric deep control sharp. net weight 25 kg

    自動化經杯型刀具專業加工磨刀機.減速馬達功率為0 . 75千瓦.微調控制磨具轉速可高達18000rpm .凈重25公斤
  7. Energy losses leading to a decrease in head are also done away with, likewise losses in flow rate from the screening installations, both of which can have a detrimental effect on the efficiency of the facility. the constructional effort required for a hydrodynamic screw is small compared to that required for a turbine. if the compact version of a hydrodynamic screw hydrodynamic screw trough power take - off unit combined as a single unit is used, the constructional effort can be further reduced

    水力螺旋機技術的優點有：無需監控系統，可自行調節水體供給和供給頻率運行效率高於水輪機和小型渦輪機效率梯度平穩轉速低20rpm - 80rpm ，運行穩定防磨損無需定期清潔，易維護對河道湖泊里的魚蝦無損害基礎工事少，安裝簡便無堵塞，無需隔欄裝置能量利用充分等。
  8. Model xjq has following features ： （ 1 ） dummy bottom is adopted, making the recycling capacity of the recycling cylinder is 2. 5times of the tand. ( 2 ) the stator is a cylinder in structure with its inner wall being vertically ribbed, and slots are placed, leading to better cutting lffect to the slurry. ( 3 ) due to low immerging depth of the rotator, low rurning speed of the impeller, and wide space between the impeller and stator, wearing is low and power consumption greatly reduced. ( 4 ) it is spontaneously aerated

    Xjq型浮選機為仿維姆科型，該機主要有以下幾個特點： （ 1 ）採用了假底，循環簡可使循環量達到槽容積的2 . 5倍; （ 2 ）定子結構為圓筒型，內壁設有立筋條和長孔，對礦漿的前切作用好; （ 3 ）轉子浸沒深度淺，葉輪轉速低，葉輪和定子間隙大，所以其磨損輕，動力消耗大大減少; （ 4 ）可自吸空氣。
  9. We must first clear of the old line, when constructed line, motor drive the cutter made of hard metal alloy to revolve at high speed, then erase old line

    在有殘損熱熔標線的路面進行劃線施工時應首先用清除機將舊標線清除干凈。該機使用發動機帶動硬質合金製成的打磨頭高速旋轉，打磨頭在旋轉離心的作用下與路面凸起部分磨合，將舊線清除。
  10. The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement

    研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。
  11. By using a wafer - rotating grinding machine, the influence of the main process factors including grit size of diamond grinding wheel, rotating speed of the wafer chuck table, rotating speed and the down feed rate of the cup grinding wheel on the material removal rate, spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated

    摘要利用基於自旋轉磨削原理的矽片超精密磨床，通過試驗研究了砂輪粒度、砂輪轉速、工件轉速及砂輪進給速度等主要因素對材料去除率、砂輪主軸電機電流以及磨削后矽片表面粗糙度的影響關系。
  12. Abstract : based on two important factors of influencing efficiency of ball mill. - revolution speed and feed size, the paper studies internal regulation actting on energy consumption of ball mill, establishes a mathematical model for the optimization of low energy consumption ball mill system

    文摘:從影響球磨機效率的兩個重要因素? ?轉速和物料的入磨細度著手，研究其與球磨機能耗之間的內在規律.通過粉磨試驗，建立了相應的數學模型，為低能耗球磨系統的優化提供了依據
  13. The cmp experiment was carried out systematically on litao3 wafer. the polished surface foughness and material removal rate in different polishing conditions were measured and the effects of polishing pad material and its condition, pressure, rotating speed of the polishing plate, the type and size of abrasive, and the properties of the polishing slurry on the surface routhness and material removal rate were analysed in details

    通過對鉭酸鋰晶片的化學機械拋光過程的實驗研究，通過測量鉭酸鋰晶片在不同拋光條件下的表面粗糙度和材料去除率，詳細分析了拋光墊材料和狀態、拋光壓力、拋光盤轉速、磨料種類及粒度、拋光液組成等幾個因素對拋光表面質量和材料去除率的影響規律。
  14. This article introduces the fundamental theory and the characteristics of the radial truck, points out the distinct advantages in high adherance, curve negotiating, low wear and low noise

    與傳統的旋轉電機轉向架相比，具有非摩擦高粘著、小半徑曲線、低磨耗、低噪聲、小型化等優點，適合現代化城市快速小曲線、陡坡道、立體化軌道交通的需要。
  15. The load - control apparatus adopted a single - chip microcomputer system, whose mcu was a kind of high - speed processor - ds80c320, whose a / d switched apparatus was max180, whose low - pass filter was max293, whose f / v transformed circuit was lm331, whose controlled silicon phase - shift touch - off circuit was tca785, and whose communicating interface of rs232 was max202. the watchdog of the mcu was max705 and the system used an on - off electrical source to supply power

    球磨機負荷控制儀採用了單片機系統， mcu採用ds80c320高速處理器，採用max180作為md轉換器，低通濾波器為max293 ， f v轉換電路利用lm331 ，可控硅移相觸發電路使用tca785 ， rs232通信介面晶元採用max202 ， mcu監控電路為max705 ，系統使用開關電源供電。
  16. This processing line has two sszm1200c straight line double edgers and 90 transfer table. 30 spindles on each sszm12000c, high collocated, wheels. high - level of polishing ; compact and steady base, precise and smooth transfermission system ; big power frequency - conversion motor to control the speed of pedeail ; plc control system sets processing parameters via interface, to control the width and the speed, the minimum size of the glass can be 127xl27mm ; the structure of the machines is compact and stable. this line is our new designed products, and it s the ideal choice of assistant equipment for exquisite and industrial glass, besides, it can be used with other machines to form a production line set

    本生產線由2臺sszml200c玻璃直線雙邊機和1個90中轉臺組成每臺sszml200c玻璃直線雙邊機配置30個磨頭，磨輪配置多，加工拋光精度好底座穩重扎實，傳動系統精確流暢大功率變頻電機調速控制傳送皮帶驅動plc控制系統通過界面設定參數控制，最小加工玻璃寬度尺寸小至127127mm機器結構緊湊性能穩定，是我公司全新設計的力作是大批量精品玻璃和工業玻璃磨邊生產的暈佳配套設備，可口與夾膠印花，鋼化等生產線配套使用
  17. The working condition of nylon shaft liner is determined by many factors, for example : the different formula, shaping technique, the design of shaft liner, installation method, loading features, running speed, lubricant condition, the working environment of shaft liner temperature, humidity and the influence of impurity, abrasion when working etc. so, when designing shaft liner, it is necessary to take consideration of all conditions

    鑄型尼軸套的許用工作情況是由很多因素決定的，例如不同配方和成型工藝所制得的材料物理機械性能，軸套的設計裝配方法，負載特點，運轉速度，潤滑情況，軸套的工作環境溫度濕度雜質的影響，工作時的摩擦條件，對磨材料的性能等。因此，在設計軸套時，應綜合考慮各個方面的因素。
  18. Generally speaking, large hydraulic turbine always rotates fast and the abrasion of the surface of the runner is very serious, so periodical examination and repair are necessary

    大型水輪機高速運轉，轉輪表面氣蝕磨損一般都很嚴重，需要進行定期檢修。
  19. In this study, the resistance to high impact, corrosion and abrasive wear was determined for low carbon high alloy steel, and for comparison, the high manganese steel and the medium carbon alloy steel are also tested

    腐蝕磨損試驗機的轉速400轉分。在不同的介質（ ph 3 ）和不同的時間內，對低碳高合金鋼、高錳鋼和中碳合金鋼進行了沖擊腐蝕磨損性能的研究。
  20. As the rolling speed and compressing ration of engines increase, the working conditions of rocker arm insert get worse, thus the materials must be excellently wear - resistant and stable. now, the pm inserts are widely used overseas

    隨著發動機轉速和壓縮比的不斷提高，搖臂的工作條件越來越惡化，要求材料必須具有很高的耐磨性和穩定性，現在國外已廣泛採用專門的粉末冶金耐磨搖臂鑲嵌件。
分享友人
分享到 Line

分享到臉書