磨漿法 的英文怎麼說
中文拼音 [mójiāngfǎ]
磨漿法
英文
bersano process-
On the base of the analysis on the advanced technology of hard ferrite in foreign country, the main procedures of preparing hard ferrite pre - sintering material are determined as follows : first, the ferrite oxides coming from the main cold rolling line and strontium carbonate are conveyed to storage tank by gas power and weighed automatically according to the demands of constituent composition. and then they are mixed and grinded by using method of wet treatment. finally the mixtures is transported to the devices of storage by transporting pump
在分析國外先進的永磁鐵氧體生產工藝的基礎上,確定了生產高檔永磁鐵氧體預燒料的主要過程:首先,利用攀鋼冷軋鐵紅為主要原料,將氧化鐵紅及碳酸鍶採用氣力輸送至貯料料倉,經自動稱量裝置,按工藝配方稱量後分別由氧化鐵紅及碳酸鍶發送罐氣力輸送進入預混攪拌筒加水攪拌,然後再送入混磨機濕法混磨;最後,混合物經輸送泵輸送至料漿存儲裝置,經定量進料泵定量輸送至回轉窯進行濕法預燒,預燒料經緩冷至室溫后,再球磨。In the alumina process with sintering, the slurry comes out from the grind with low quality because of lots of uncertainty factors and the delay of composition analysis, the qualified raw mix slurry is commonly gained through arranging
摘要由於燒結法氧化鋁配置生料漿過程中不確定性因素多,成分分析滯后,造成生料漿出磨合格率低,一般需經調配使生料漿質量指標符合工藝要求。Pulps - laboratory beating - part 2 : pfi mill method
紙漿.實驗室打漿.第2部分: pfi碾磨法Pulps - laboratory beating - pfi mill method
紙漿.實驗室打漿. pfi碾磨法Although most part of the parameters for the design of bivis extruder currently need to be determined by adopting the analogy method, but flow capacity and condition of strength are the constraint conditions that it has to satisfy
雖然目前雙螺桿磨漿機設計的大部分參數需要採用類比法確定,但流量和強度條件是其應當滿足的約束條件。Based on the analysis of pulping movement of material in bivis extruder, a study on the designing theory of positive directional screw in bivis extruder had been carried out, the relationship between flow capacity and basic parameters of positive directional screw in bivis extruder was established, the designing method of negative directional screw was discussed, and a basic designing train of thought of the extruder was put forward
摘要在分析雙螺桿磨漿機中物料磨漿運動的基礎上,對雙螺桿磨漿機的正向螺旋的設計理論進行了研究,建立了流量與雙螺桿機構正向螺旋的基本參數之間的關系,討論了反向螺旋的設計方法,提出了雙螺桿磨漿機設計的基本思路。Slurry surfacing - test methods - determination of wearing
砂漿路面層.試驗方法.磨損性測定This paper discusses the surface etching of polyester thread through application of plasma and alkali deweighting to enhance the size adhesion to polyester thread and improve the abrasion - resistance of the sized polyester thread
摘要探索了應用堿減量、低溫等離子體處理方法對滌綸股線表面進行刻蝕處理,以改善上漿前滌綸表面界面,增強漿液對滌綸股線的黏附性,提高上漿后滌綸股線的耐磨性的研究。Used in grinding of chemical pulp, semichemical mechanical pulp, high - yield pulp ( cold impregnation ) and fiber board materials
用於化學漿、半化學機械漿、冷浸法高得率漿及纖維板料的研磨。In light of great harm from alkali - aggregate to concrete, the alkali activation of the limestone to be used as the aggregate for the concrete in the construction of zhangfeng reservoir is fully tested with petrographic method, accelerated mortar bar method and autoclave expansion test etc., so as to ensure the durability of the anti - abrasion concrete therein
摘要堿骨料對混凝土的危害很大,為保證抗沖磨混凝土的耐久性採用巖相法、砂漿棒快速法、壓蒸法等4種方法對陽城下川灰巖進行檢驗,以充分揭示張峰水庫混凝土粗骨料是否存在堿活性。Slurry surfacing - test methods - part 5 : determination of wearing
泥漿表面塗抹.試驗方法.第5部分:磨損性測定Slurry surfacing - test method - part 5 : determination of wearing ; german version en 12274 - 5 : 2003
泥漿表面修整.試驗方法.第5部分:磨損性測定Test method for abrasion resistance of concrete or mortar surfaces by the rotating - cutter method
用旋轉切割機法對混凝土或砂漿表面耐磨性的試驗方法Pulps - laboratory beating - jokro mill method
紙漿實驗室打漿約克羅磨法Pulps - laboratory beating - part 2 : pfi mill method iso 5264 - 2 : 2002 ; german version en iso 5264 - 2 : 2002
紙漿.實驗室打漿.第2部分: pfi碾磨法分享友人