磨耗溫度 的英文怎麼說

中文拼音 [móhàowēndù]
磨耗溫度 英文
abrasive temperature
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 耗 : Ⅰ動1 （減損; 消耗） consume; cost 2 [方言] （拖延） waste time; dawdle Ⅱ名詞1 （壞的音信或消息） ...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 溫度 : [物理學] temperature
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. Heat convected, a mode of motion developed by such combustion, was constantly and increasingly conveyed from the source of calorification to the liquid contained in the vessel, being radiated through the uneven unpolished dark surface of the metal iron, in part reflected, in part absorbed, in part transmitted, gradually raising the temperature of the water from normal to boiling point, a rise in temperature expressible as the result of an expenditure of 72 thermal units needed to raise i pound of water from 50 to 212 fahrenheit

    燃燒所引起的運動形式之一-熱對流傳熱，不斷地加速度地從熱源體傳導給容器中的液體，由那凹凸不平未經打磨的黑色鑄鐵面把熱向周圍發散出去一部分反射回來，一部分被吸收，另一部分被傳導，使水的溫度從常溫逐漸升到沸點。這種溫度的上升可作為消費結果標志如下：將一磅水從華氏五十度加熱到二百十二度，需耗七十二熱量單位。
  3. The grade composite, road performance and its mechanism are systemically studied. 1 ) the aggregate grade of ogfc is studied through the volume method base on the analysis of the aggregate grades. then the grade is verified and the relation between the grade and pore rate is studied statistically, the typical grades of ogfc are developed ; 2 ) the reasonable pore rate of ogfc is studied on the basis of the balance of mechanics and function performance ; 3 ) the mineral fiber is added to the ogfc mixes to increase asphalt content, thus the anti - water performance of ogfc mixes are improved ; 4 ) high viscous asphalt fit for the preparation of ogfc is prepared through composite modification by sbs and rubber powder ; 5 ) the mechanics mechanism of ogfc is studied in the paper, it shows : asphalt paste, as well as the coarse aggregate skeleton, is essential to the mechanics of ogfc

    在分析各國ogfc級配的基礎上，運用礦料體積法進行ogfc級配設計，用正交實驗對礦料級配進行了優化設計，運用數理統計方法分析礦料級配和孔隙率之間的關系，並回歸出礦料關鍵篩孔通過率與ogfc骨架空隙結構關系的數學方程，進而提出了ogfc的合理級配；通過對不同孔隙率典型級配混合料的性能研究，綜合力學和功能性能，得出了ogfc的合理孔隙率范圍：針對高速公路面層對ogfc力學性能方面的要求，本文從瀝青膠結材料、纖維穩定劑兩方面對ogfc的性能進行改善：通過sbs和橡膠粉復合改性的方法開發出了適合ogfc的高粘度改性瀝青，摻加聚合物纖維，提高ogfc的最佳瀝青用量，進而改善了混合料的高溫性能和抗水損害性能，優化設計出能滿足高速公路路用性能，車轍動穩定度達5000次/ mm以上，動融劈裂強度比90 ，透水系數31ml / s ，並具有防滑降噪功能的開級配瀝青磨耗層（ ogfc ）混合料。
  4. The cement concrete pavement, as one of the high - grade pavement structures, has been widely used because of such advantages as high strength, good stability, great durability, high temperature stability, abrasive hardness and low cost of maintenance

    水泥混凝土路面作為一種高級路面結構形式，以其強度高、穩定性和耐久性好、耐高溫、耐磨耗以及養護費用少等優點而得到了廣泛的應用。
  5. Gloss. color. tensile strength. yield tensile strength flexural rigidity. flexural. elasticity. lmpact resistance. coating thichness. coating hardness. adhesion lmpact. abrasion. chemical resistance. cosfficicent of linear. thermal expan - sion thermal transmission properties. hdt

    光澤.顏色.拉伸強度.屈服抗拉強度.彎曲強度.彎曲模量.抗沖擊性.塗膜厚度.硬度.附著力.耐沖擊.耐磨耗性.耐化學性.熱膨脹系數.熱傳導系數.熱變形溫度
  6. The mixture of tungsten and graphite powders would tranform into solid solution by ball milling for little time, and wc with high purity was obtained by treatment at a lower temperature. the milling time, producing energy and the disadvantage of contamination was reduced, which is favorable for the future application in the manufacture of tungsten carbide

    W 、 c粉體經過短時間球磨形成固溶體后，較低溫度下退火就可以得到純度很高的wc ，可以大大縮短球磨時間，從而避免了過渡的污染而且降低了能耗，具有工業實際應用前景。
分享友人
分享到 Line

分享到臉書