磨蝕機 的英文怎麼說

中文拼音 [móshíjī]
磨蝕機 英文
abrader
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 機 : machineengine
  1. Test method for abrasion resistance of organic coatings by air blast abrasive

    鼓風磨蝕試驗測定有機塗料耐磨性能試驗方法
  2. Wearproof porcelain plate developed by this factory can be used as inside lining plate, coal delivery pipework, bin, bunker, separation port, wind pipe bend, exhauster, inner pipe of mill fan, air preheater, air fule and various dedust equipment for antifriction. besides, it can extend the service life of equipment

    耐磨瓷板系是我廠自行研製的適用於磨煤機內襯板，輸煤管道、料倉、料斗、粗、細粉分離口、一、二次風管彎頭、引風機、排粉機內殼、空氣預熱器、尾部煙道等以及各類除塵系統設備的防磨抗蝕、延長設備的使用壽命。
  3. The loca | n320gear oil used in gearbox of coal mill, the gears appeared pitting and scuffing, meanwhile shocking and noise increased, the oil oxidized and sludge formed

    磨煤機齒輪箱使用n320齒輪油，造成齒輪點蝕，齒面嚴重磨損，振動及噪音增大，油質氧化，產生油泥。
  4. Standard test method for resistance to abrasion of resilient floor coverings using an abrader with a grit feed method

    用帶喂磨料的磨蝕測試機測定彈性地板覆蓋物耐磨性的標準試驗方法
  5. And with the increased test time, the superiority of the low carbon high alloy steel was well illuminated. the worn surfaces of the three steels show that the mechanism of the low carbon high alloy steel is impact abrasion, the high manganese steel is impact - corrosion, and the medium carbon alloy steel is the heaviest impact - corrosion

    最後通過hitachi - x - 650掃描電子顯微鏡考察了低碳高合金鋼、高錳鋼和中碳合金鋼試樣的沖擊腐蝕磨損表面形貌，並用olympus光學顯微鏡進行了光學金相分析，對這三種鋼的磨損機理進行一定的探討。
  6. Study on erosion - resistance of the flexible organic coating composite

    有機復合彈性塗層材料的抗磨蝕試驗研究
  7. In order to study the slurry erosion properties of the particle reinforced polyurethane composites, a slurry erosion test apparatus was designed and manufactured based on the considerations of comparison between the present slurry erosion apparatuses and cost factor. the slurry erosion test apparatus proved to stable and reliable through tests, and it can be applied to material selection and erosion mechanism research

    經過實驗驗證表明，該沖蝕磨損試驗機供漿穩定，磨損數據重現性較好，是較為可靠的研究漿體沖蝕磨損的試驗裝置，適合於進行耐磨材料對比選擇以及漿體沖蝕磨損機理的研究。
  8. The technology of wear resistance in silt - laden river

    多泥沙河流水輪機磨蝕的防護技術
  9. Erosion - corrosion of carbon steel in liquid solid two phase flow through pipe

    固雙相管流中的磨損腐蝕機理研究
  10. Cavitations in foreign hydraulic turbines appear in clear water condition, so its destructive extent is not far more serious than in yellow river in our country. stronger stiffness and more agility are required for special - purpose robot for hydraulic turbine repair used in our country, especially robot for polishing after weld. foreign robot for hydraulic turbine repair could not satisfy our working require, so we develop special - purpose robot system that is used to polish and weld repair cavitated flow path surfaces of hydraulic turbines on all locations

    國外水電站的水輪機汽蝕是在清水條件下產生的，其破壞程度遠不及我國黃河等水域嚴重，用於我國水輪機修復工作的專用機器人，特別是補焊后承擔打磨的機器人，要求有更強的剛度和更大的靈活性，國外水輪機修復機器人滿足不了我國水輪機修復工作要求，因此我們開發了用於在機坑內對水輪機空蝕磨損破壞表面進行修復的「水輪機修復專用機器人」 。
  11. A set of conventional processing methods of vanadium and vanadium alloy specimens, including mechanical polishing, mechanical chemical polishing, chemical etching as well as relevant techniques and experiences is introduced

    摘要介紹了一種釩及釩基合金金相試樣的常規制樣方法，即試樣的機械磨光，機械化學拋光，化學侵蝕等技術和經驗。
  12. The number of scrapped broken wires for hoisting hot metal or dangerous goods is taken as half of scrapped broken wires of general hoisting rope, including reduction for wear - and - tear on the surface of wire rope

    3吊運熾熱金屬或危險品的鋼絲繩的報廢斷絲數，取一般起重機鋼絲繩報廢斷絲數的一半，其中包括鋼絲表面磨蝕進行的折減。
  13. Through repairing the worn parts of four hydropower stations of xinzhuang, zaoqi, suide and qiemo, and taking some comprehensive anti - abrasion measures, such as checking and repairing the runner blade, cutting the head of blade into round shape, adding an apron to the outer edge of blade and increasing a guiding plate in the head of blade, a good effectiveness has been gained so that it increases the output of generating unit and enhances the abrasion resistant capacity

    通過對新莊、棗渠、綏德、且末4個水電站的磨蝕破壞部件的修復、轉輪葉片測型與修型、葉片頭部割圓角、葉片外緣加裙邊、頭部加導流板等抗磨蝕措施的綜合治理，取得較好效果，使機組出力增加、抗磨蝕能力提高。
  14. It tell us : the abrasive capability of fly ash ; the similar calculation of ash erosion ; the calculation of ash erosion in the tube in turn and tube out of turn ; the reason of tube abrasion for gas flue ; the influence of air parameter for fly ash erosion ; the influence of changing temperature ; the influence of the flue gas composition, etc. next, it advances the solving measure ; reduce the flue gas velocity ; reduce the concentration of fly ash ; responsible construction : replace smooth tube with spiral tube ; use the new material of abrasion ; fuel desulfurization ; reduce so3 of flue gas ; raise flue gas temperature, making it up the dew point ; use the abrasion - resistance material to resist abrasion

    討論了飛灰磨損性能、管壁受飛灰沖蝕的近似計算、灰粒對順列管和錯列管的磨損計算、煙氣走廊引起對流管束的磨損機理、空氣動力參數對飛灰沖蝕的影響以及受熱面壁溫變化及煙氣成份對飛灰磨損的影響等問題。接著提出了解決的措施：降低平均煙氣流速；降低飛灰濃度；使用鰭片管、螺旋翅片管代替光管；選擇合適的結構及排列方式，減少煙氣中so3的含量；提高受熱面壁溫使之大於煙氣的露點溫度；採用抗腐蝕材料作受熱面等防腐蝕的措施。
  15. The turbulent characteristics of high - velocity sediment - laden and aerated flow are more other than the clear water flow of single - phase and current of low speed. in a special circulating system with high velocity flow, some flow parameters such as boundary shear stress and pulsation pressure are measured. an investigation is made on the turbulent characteristics of the three - phase flow of water, air and sand

    本文針對高速含沙摻氣水流的運動規律有別于低速水流及清水單相流，在自己研製的高速渾水循環系統中，通過對高速含沙摻氣水流壁面剪切應力和脈動壓強等參數的量測，分析了水沙氣三相流的紊動特性，探索了泥沙對固壁的磨蝕機理及減蝕措施，其主要內容包括以下幾個方面： 1
  16. Rubber - or plastics - coated fabrics - determination of abrasion resistance - taber abrader

    塗橡膠或塑料的織物.耐磨性的測定. taber磨蝕機
  17. Study on erosion wear mechanisms of wc co coating prepared by hvof

    塗層沖蝕磨損機理研究
  18. The surface material is liable to erosion wear with high - velocity sediment - laden flow, hi this paper, sand wear mechanisms are discussed and some effects of significant flow factors on material wear are analyzed ; the possibility of preventing erosion wear with aeration is proposed ; based on test data, the formula for calculating the concrete material wall surface wear rate is derived. it is indicated that the wear rate is related to the air concentration, the strength of material, the flow velocity and the sediment content. it is shown that wear rate can be reduced with the help of flow aeration

    分析了空蝕與磨蝕的不同物理特徵；探討了沙粒磨蝕機理，提出了影響磨蝕vi河海大學博士學位論文一的因素；研究了摻氣抗磨的可能性：建立了混凝土材料壁面磨蝕率的計算公式；說明含沙水流對固壁材料的磨蝕率隨摻氣濃度、材料強度的增大而減小，隨水流流速、含沙量的提高而增大；利用摻氣可有效地降低過流表面的泥沙磨蝕率。
  19. Standard test method for abrasion resistance of organic coatings by the taber abraser

    用泰伯爾磨蝕機測定有機塗層耐磨性的標準試驗方法
  20. Textile floor coverings. determination of wool fibre integrity using an abrasion machine

    紡織地毯.用磨蝕機對羊毛纖維完整性的測定
分享友人
分享到 Line

分享到臉書