程序控制鏈器 的英文怎麼說

中文拼音 [chéngxùkòngzhìliànqì]
程序控制鏈器 英文
programmable link
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 鏈 : Ⅰ名詞1. （鏈子） chain Ⅱ動詞（用鏈栓住） chain; enchain Ⅲ量詞（計量海洋上距離的長度單位） cable length
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Although there have been many application instances in the field of input / output device technology, we need an specific project and technology route aimed at an given application. in this thesis, we combine the introduction and analysis of relative technology to describe the accomplishment of a coordinate collecting device which is based on incremental rotary encoder. this device is an specific device applied to collect the corrdinate displacement of ground image ’ s three - dimensional model created by full digital photogrammetric station. cpld chip and vhdl are applied in this device to carry out the following work : phase control of the electrical pulse created by incremental rotary encoder, counting the number of electrical pulse, controling the state of signal processing circuit, exchanging data between this circuit and pci control

    本文結合相關技術的介紹和分析，描述了一個基於增量式旋轉編碼器的坐標參量採集介面卡的實現，此介面卡是一種用於採集全數字攝影測量系統地面影像模型坐標位移量的專用設備，該設備採用cpld器件和vhdl語言實現增量式旋轉編碼器的脈沖信號鑒相和計數、信號處理部分的狀態控制以及和pci總線晶元ch365之間的數據交換和通信功能，同時該設備的驅動程序基於wdm模式，並且配置有結構良好的動態鏈接庫程序作為系統軟體和驅動程序之間的數據和控制交互中間介面，能夠方便地運行在windows98 / 2000 / xp操作系統平臺上，具有實時性強、工作穩定、通用性較好和性價比高等特點。
  2. The author is absorbed in research on technology of coprocessor design. in the floating - point addition the paper proposes a carry chain of dynamic and static mixed circuits and a good balance between speed and area of predicting leading - zero logic circuits, considering algorithm and construction of logic circuits. an approach of micro program controller design for coprocessor is put forward and a test bench is given to verify its function

    筆者研究協處理器的設計技術，在浮點加法器中提出動態與靜態結合設計進位鏈的方案以及前導零預測面積與速度的折衷方法；在微程序控制器的設計中提出一種協處理器微程序控制器的設計方法，並且給出其功能驗證的測試平臺。
  3. The application controls which dynamic libraries are loaded and which functions in the libraries are called by using linux dynamic loader routines to perform the loading and linking and to return the addresses of the required entry points

    通過使用linux動態裝入器常式，應用程序控制裝入哪一個動態庫以及調用庫中的哪一個函數，以執行裝入和鏈接以及返回所需入口點的地址。
  4. 1 ) realization of software packet embedded in m - es and md - is respectively to accomplish main function of mdlp, including assignment of tei ( temporary equipment identifier ), establishment of multiple frame operation, framing, flow control and error - free transmission of packets, is detailed. 2 ) a test model is established to evaluate the robustness and stability of mdlp and verify the validity of software packets. 3 ) according to the design of radio modem construction used in m - es, the modules of interface between data terminal equipment and radio modem are achieved to enable transmission of short message and continuous pseudo - random bit stream via rs232 uart

    本文首先概述了蜂窩數字分組數據網的結構和空中協議，詳細分析了移動數據鏈路協議，並在此基礎上，重點敘述了以下方面的工作： 1 ）設計並完成了分別應用於m - es和md - is端無線控制器的兩套程序實現數據鏈路層的主要功能，包括分配臨時設備號、建立鏈路、組幀和面向連接的服務保證分組正確無誤地傳輸，並進行適當的流控； 2 ）建立測試模型測試移動數據鏈路協議的可靠性和穩定性，證明了程序包的效用； 3 ）根據cdpd系統無線數據機的軟硬體總體設計方案，完成了介面模塊，實現了rs232異步串口通信，使用戶可以根據需要發送短消息或連續的偽隨機比特流； 4 ）在tms320c54x的軟體、硬體模擬平臺上，建立了cdpd試驗模型，實現了cdpd系統的mdlp基本功能。
  5. All compilation messages coming from make, compiler, and linker are redirected to the console window

    所有來自make 、編譯器和鏈接程序的編譯消息都被重定向到控制臺窗口：
分享友人
分享到 Line

分享到臉書