程度升溫 的英文怎麼說

中文拼音 [chéngdùshēngwēn]
程度升溫 英文
temperature programming
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 升 : Ⅰ動詞1 （由低往高移動） rise; hoist; go up; ascend 2 （等級提高） promote Ⅱ量詞1 （容量單位） lit...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 程度 : 1. （知識、能力的水平） level; degree 2. （事物變化達到的狀況） extent; degree
  1. At 100 to 150, both the toughness and the molecular weight decreased during the process of amination, but the transformation ratio of the amination reaction increased rapidly ; above 150, both the toughness and the molecular weight increased and transformation ratio of the amination slightly increased, and reached completely amination

    亞胺化過程中，當溫度從100升至150時，不同熱處理階段薄膜的韌性和分子量均下降，亞胺化反應轉化率上升較快； 150后，其韌性和分子量均升高，亞胺化反應轉化率上升趨于緩慢，最終達到完全亞胺化。
  2. The globalization course was that the preformed texture recrystallized and became the granular equiaxed grain, when the temperature rose and the holding time prolonged, the granular grain melted at some area and at the liquid - solid interface the grain globalized at the role of the curvature overheated

    過程機制為：擠壓形變組織在加熱過程中首先發生再結晶長大變為顆粒狀等軸晶；隨溫度升高和保溫時間延長，等軸晶發生局部熔化，液固界面的曲率過熱使晶粒外形向球狀轉變。
  3. ( 3 ) the result showed that when ambient temperature rises to a certain degree, the frictional surface of uhmwpe and its composites melt and gelatinize

    門）當環境溫度升高到一定程度， uhmwpe及其復合材料與鋼配副的摩擦界面熔融變為凝膠狀態，其摩擦系數隨摩擦時間的延長保持不變。
  4. 3. at the same holding time, when the holding temperature changed, the number of the long equal - area - circle diameter grain increased, and the average of the equal - area - circle diameter lengthened, the average of the roundness heightened

    3 、相同保溫時間條件下，改變等溫溫度，等積圓直徑大的晶粒隨溫度的升高而增加，球狀化程度高的晶粒數增多，平均等積圓直徑和平均球化度同時增大。
  5. There was a critical temperature tm between 1200 ~ 1215. above the tm the relationship between the temperature and the extent of reaction of cu2o and al, which would react completely by keeping the time of holding temperature longer or rising temperature higher, is of liner relation. 3

    Cu _ 2o與al的反應存在一個臨界溫度，這個臨界溫度為1200 1215之間的某一溫度t _ m ，高於t _ m ，熔液溫度的提高與cu _ 2o與al的反應進行的程度呈線性關系，並且延長保溫時間或者繼續升高反應溫度最終都能使反應完全。
  6. The temperature rise at the center of a massive concrete wall is calculated by using the adiabatic rise of temperature and heat conduction equations of concrete based on the equivalent time, and considering effects of temperature on the hydration heat reaction ratio and creep characteristics of early - age concrete

    摘要基於等效時間的混凝土絕熱溫升、熱傳導方程，考慮溫度對早期混凝土水化熱化學反應速率和徐變特性的影響，計算了大體積混凝土墻中心的溫升。
  7. The test results indicate that the influence of the asphalt type and the temperature period on the value of linear contractive quotiety is very notable, while that of asphalt content ( variation within 0. 3 % ) and the temperature raising and reducing process is relatively small

    試驗結果表明：瀝青品種對瀝青混凝土的線收縮系數的影響較大，瀝青混凝土在不同溫度段的線收縮系數相差很大，而瀝青含量（變化范圍0 . 3 % ） 、升溫或降溫過程對其的影響較小。
  8. Unique a 3 segments ' temperature curve program achieves a steady heat rising and good protection of bga component

    獨設三段式溫度曲線程序，實踐分段升溫控制，令bga得到妥貼的保護。
  9. We select ni / cr alloy resistor as element together with ceramic embedding hearth ; select small flat - and - disc heat - even hubby ceramic sample holder, select ni / cr & ni / si thermoelectric couple ( type k ) as thermoscope with threads 0. 5 mm in diameter which is installed in the middle of the holders symmetrically ; select aluminum silicate fire - retardant fiber as materials for heat preservation ; design some hardware, for example temperature controller & transporter, signal amplifier etc ; design controlling curve to heat stove ; and introduce the method of least squares nonlinear regression and subsection function to deal with data. in order to obtain the reasonable operation conditions and operation curve, we have also done many theory analysis and experiment discussions

    通過理論和試驗探討，選用鎳鉻合金電阻絲作為加熱元件，配以陶瓷質埋入式爐膛；選用陶瓷質小尺寸扁平?圓盤均熱塊體型樣品支持器；選用0 . 5mm絲徑鎳鉻?鎳硅熱電偶（ k ）作為測溫元件；熱電偶對稱安置在樣品支持器容器的中部；選用硅酸鋁耐火纖維作保溫材料；合理選用和設計了溫度控制器、溫度變送器、信號放大電路等硬體；採用升溫曲線來控制爐膛供熱過程；採用最小二乘法非線性回歸與分段函數相結合的曲線模擬方法，進行圖形處理。
  10. All related action in dyeing process e. g water inlet, start main pump, heating,

    自動化程度高，從進水，啟動升溫保溫降溫水洗加
  11. In the program, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress are considered. and such temperature control measurement as water pipe cooling, heat preservation of the dam surface, the pouring temperature control, the overflow across the dam top during flood season can also be simulated by numerical method

    該程序在編制過程中考慮了混凝土分層澆築、施工間歇、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度場及溫度應力場的影響，同時也考慮了水管冷卻、壩體表面保溫、控制澆築溫度、施工汛期壩頂面過水等各種溫控措施的數值模擬。
  12. In this article, according to heat conduction theory, elastic creep theory and finite element theory, the temperature field and creep stress field in the arch dam during construction and operation are simulated and analyzed by means of three dimensional finite element relocating mesh method, and the distribution law of the temperature field and creep stress field in the arch dam during construction and operation are systematically studied, and according to the construction process of concrete arch dam, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress in the arch dam are also considered

    論文根據熱傳導理論、彈性徐變理論及有限元理論，用三維有限元浮動網格法對拱壩施工期和運行期溫度場、徐變應力場進行了全過程模擬分析，較為系統的研究了混凝土拱壩施工期和運行期溫度場、徐變應力場的分佈規律，在分析中按照混凝土拱壩施工過程，考慮了混凝土分層澆築、施工間隙時間、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度應力的影響。
  13. The quality of buffer layer and thin films was analyzed by afm, xrd, rheed and xps respectively. the effect of the experimental parameters such as carbonization time, working pressure, c source gas flow rate, carbonization temperature, different carbonization gas and substrate on the carbonization process was studied firstly. it was observed that the size of particles was increased with the increase of carbonization time and the rms was opposite, but the trend was reduced while the carbonization time was long enough ; the size of particles was increased with the increase of working pressure too, and choosing a proper working pressure could get a smooth surface ; the size of particles was unobviously changed while the gas flow rate was low, but it was notability increased with the increase of gas flow rate while the gas flow rate was high enough, and a smooth surface could be also obtained by choosing a proper gas flow rate ; with the increase of carbonization temperature, the size of particles was increased, the rms is decreased and a good single - crystalline carbonization layer could be obtained, but a rough surface was formed at a excessive high temperature ; the rms of

    對于碳化工藝，側重研究了碳化時間、反應室氣壓、 c源氣體的流量、碳化溫度以及不同種類的c源氣體、基片取向等因素對碳化層質量的影響，研究結果表明:隨著碳化時間的增長，碳化層的晶粒尺寸隨之變大，表面粗糙度隨之降低，但當碳化到一定時間之後，碳化反應減緩，碳化層的晶粒尺寸以及表面粗糙度的變化幅度變小;碳化層的晶粒尺寸隨反應室氣壓的升高而變大，適中的反應室氣壓可得到表面比較平整的碳化層;在c源氣體的流量相對較小時，碳化層的晶粒尺寸隨氣體流量的變化不明顯，但當氣體流量增大到一定程度時，碳化層的晶粒尺寸隨氣體流量的增大而明顯變大，同時，適中的氣體流量得到的碳化層表面粗糙度較低;碳化溫度較低時，碳化層的晶粒取向不明顯，隨著碳化溫度的升高，碳化層的晶粒尺寸明顯變大，且有微弱的單晶取向出現，但取向較差，同時，適中的碳化溫度可得到表面平整的碳化層;相比于c _ 2h _ 2 ，以ch _ 4作為c源氣體時得到的碳化層表面平整得多;比起si （ 100 ） ，選用si （ 111 ）作為基片生長的碳化層的晶粒取向一致性明顯更好。
  14. After which, the battery will be charged by large constant current to allow the fast charging. finally, the constant voltage charging is adopted to guarantee the battery was charged to its full capacity. under the condition that the temperature has raised to a certain threshold at the constant current charging stage, the over temperature circuit is performing and it provides a compensation current which switches the system to constant temperature charging mode with the intention of protecting the ic

    即在充電初期採用較小的電流對電池進行預處理，對出現過放電的電池進行修復和保護;然後採用較大的恆定電流對電池充電，實現快速充電的目的;最後採用恆定壓充電，確保電池充滿;在恆流充電階段，當晶元溫度上升到一定程度時，晶元過熱保護電路開始工作，該電路以提供充電補償電流的形式使充電進入恆溫充電模式，對晶元進行保護。
  15. It is found that the enhancement of the long - range interaction will result in the increment of the phase transition temperature, the increase of the critical transverse field and the decrease of the critical size

    採用超越平均場理論計算了長程相互作用對鐵電薄膜的物理性質的影響，發現長程相互作用的增強將使鐵電薄膜的居里溫度升高、臨界橫場增大、臨界尺寸下降。
  16. Setup functions enable user - defined adaptation of a wide variety of options such as display contrast, record printout, saving data on the computer, general code, temperature calibration, acoustic signal, date and time, id, data transfer, update fix programs, language, c f changeover, check program, battery change, diagnosis data, printing programs, seal test, service functions for maintenance

    設置功能允許使用人員對多種選項進行定義和調節，例如顯示屏幕對比度列印記錄把數據記錄到計算機上總碼溫度校正音響信號日期和時間識別傳輸數據固定程序升級語言攝氏和華氏溫度轉換檢查程序更換電池診斷數據列印程序測試密封保養用服務功能。
  17. Setup functions enable user - defined adaptation of a wide variety of options such as display contrast, record printout, saving data on the computer, general code, temperature calibration, acoustic signal, date and time, id, data transfer, update fix programs, language, screen saver, c f changeover, check programme, battery change, diagnosis data, printing programs, seal test, service functions for maintenance

    設置功能允許使用人員對多種選項進行定義和調節，例如顯示屏幕對比度列印記錄把數據記錄到計算機上總碼溫度校正音響信號日期和時間識別傳輸數據固定程序升級語言屏幕保護攝氏和華氏溫度轉換檢查程序更換電池診斷數據列印程序測試密封保養用服務功能
  18. The conclusions obtained as follows : firstly, the structure ' s free frequency is decreased by the reduction of the mechanical property of the material with the increasing temperature ; secondly the thermal stress produced by the temperature gradient may decrease or enlarge the structures natural frequency ; thirdly, the variety of natural frequency of the alloy structures effected by the heat effect apparently higher than that of the composite material structures

    最後，採用ansys程序分析了合金材料、復合材料的板、彈體結構的熱振動特性。在不同的熱載條件下，取得以下結論：升溫導致的材料機械性能下降都會降低結構固有頻率，而溫度梯度產生的熱應力可能降低也可能提高結構的固有頻率；金屬材料結構的固有頻率受溫度的影響要比復合材料結構的固有頻率受溫度的影響要明顯。
  19. The compatibility and harmony among workability, mechanical grade and durability are optimized, with the ground of adjusting composition and dosage of fd - 1 ; after analyzing anti - freezing damage mechanism, it is concluded that temperature is main factor, which affects structure and property of concrete. after two processes of temperature - elevation of hydration heat and temperature - descent of cold - environment, there is original damage in concrete and its existence leads to temperature fields, as results in temperature damage on transition phase > aggregate and cement mortar of concrete

    通過對負溫混凝土早期防凍分析研究認為，環境溫度對混凝土的結構形成及其性能的影響十分突出，水泥水化溫升和環境散熱降溫兩個過程導致混凝土結構內部產生不均勻溫度場，對過渡相、水泥砂漿以及骨料都能產生不同程度的溫度損傷，產生內部溫差應力裂紋，初始損傷也是不可避免的。
  20. Rules and process are established on inspecting and testing finished products, including the tests of durability, heat build - up and intermediate controlling

    建立成品檢驗和試驗規程，可進行輪胎耐久試驗，負載下升溫度試驗、中間材料控制試驗等。
分享友人
分享到 Line

分享到臉書