穩定電弧焊 的英文怎麼說

中文拼音 [wěndìngdiànhúhàn]
穩定電弧焊 英文
stable arc welding
  • 穩 : 形容詞1 （穩定; 穩當） steady; stable; firm 2 （穩重） steady; staid; sedate 3 （穩妥） sure; rel...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 穩定 : 1 （使穩定） stabilize; steady 2 （穩固安定） stable; steady 3 （物質的性能不易改變的作用） stabi...
  1. Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel

    可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。
  2. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  3. Using the traits of arc adjust itself of the co _ 2 welding, adopting slow - descending feature or even feature of electrical source equipping with system that delivering the welding rod at the invariable speed, then, the arc burning steadily is realized, and the quality of welding is improved

    利用co _ 2氣體保護焊電弧的自身調節特性，採用緩降或平硬特性的電源配等速送絲系統，通過改變電源空載電壓來調節電弧電壓，再利用電弧電壓和熔化速度之間的關系調節焊絲熔化速度使之等於送絲速度，最終實現電弧的穩定燃燒。
  4. Patent control technology of dynamic characteristics and waveform, hard arc, stable welding current, little spatter, good welding surface, optimized matching parameters, welding speed increased by 100 - 200 %

    專利動特性及波控技術，電弧挺度大，焊接過程穩定，飛濺少，成型美觀，優化參數匹配，焊速可提高100 - 200 %
  5. Voltage feedback control can automatically compensate to the distribution voltage wav and let the welding electric arc stability

    電壓反饋控制，對電網電壓波動能自動補償，使焊接電弧穩定。
  6. The dcep mig has the characteristic of deeper penetration which can reduce defective fusion and good arc stabilization. the dcen mig has the characteristic of shallow penetration of welding seam, and the welding wire has a high melting speed. so the variable polarity pulsed mig is a new technology for the welding of aluminium alloy sheet

    變極性脈沖mig焊是一種新的焊接工藝方法，其綜合了dcep脈沖mig焊熔深較大、可以減少焊縫的熔合不良、電弧穩定性好和dcenmig焊焊縫熔深淺、焊絲熔化速度較快的特點，減小了焊縫的熔深，增加了焊絲的熔化速度，是一種適合於薄板鋁合金焊接的新方法。
  7. Arc welding equipment - arc striking and stabilizing devices

    電弧焊設備.電弧放電和穩定設備
  8. Arc welding equipment - part 3 : arc striking and stabilizing devices

    電弧焊設備.第3部分:電弧放電和穩定設備
分享友人
分享到 Line

分享到臉書